Industries / Industrial equipment and services / Industrial machinery / Boilers and pressure vessels
Design and codes
This work sets and applies the rules that fix how a boiler or vessel is laid out, how thick its walls must be, which steels may be used and how much safety margin is left, before any plate is cut.
6
Milestones achieved, from 1866 to 1999.
1
To watch for: announced, not yet confirmed outside.
2
Open deliverables. Nobody has shipped them.
The road
AchievedWatch forOpen
Achieved
1866
Inspection sold as insurance
Hartford Steam Boiler was founded on 30 June 1866, growing out of Hartford's Polytechnic Club, at a time when, by the company's account, boiler explosions in the US came almost one every four days. It inspected the boilers it insured, and its "Hartford Standards" became specifications for boiler design. Its first president called it "the first company in America devoted primarily to industrial safety", a claim made by the company itself.
LessonInsurers who paid for explosions had a reason to write design rules before any government did.
Credit
Hartford Steam Boiler Inspection and Insurance Company
1867
Many small tubes, not one shell
George H. Babcock and Stephen Wilcox Jr. of Providence, Rhode Island patented an "Improvement in Steam Generators" (US 65,042, 28 May 1867) in which the water is split among many small tubes and vessels joined by pipes, so that a rupture in one part stays local. ASME's profile of Wilcox says the design "reduced the risk of explosion inherent in the earlier designs" and, because it could work at high pressure, became the standard for large boilers. This is the water-tube boiler; in the older fire-tube boiler, hot gas runs through tubes inside one large shell of water.
LessonA boiler whose stored water is split into small parts cannot release all of it at once.
Credit
George H. Babcock and Stephen Wilcox Jr., Babcock & Wilcox
1915
One rulebook for boilers
ASME's first code, dated 1914 and issued in spring 1915, was one 114-page book of 5 by 8 inches. It followed the Grover shoe factory explosion in Brockton, which killed 58 people; ASME dates it 10 March 1905 and a City of Brockton account dates it 20 March. ASME says the code has been a de facto international standard since 1972.
LessonPrivate rules became law only after factory explosions killed dozens of workers at a time.
Credit
ASME Boiler Code Committee, proposed by Edward D. Meier and chaired by John A. Stevens
1968
Design by analysis
ASME first issued Section VIII, the rules for unfired pressure vessels (vessels not heated by a fire, such as tanks and reactors), in 1925. In 1968 it added Division 2, "Alternative Rules", which lets a designer prove a vessel by detailed stress analysis instead of fixed formulas, in return for tighter checks. Division 3, for high-pressure vessels, followed in 1997.
Credit
ASME Boiler and Pressure Vessel Committee
1997
One law for Europe
The European Union adopted the Pressure Equipment Directive, 97/23/EC, on 29 May 1997. Member states had to apply it from 29 November 1999, and equipment built to the old national rules could be sold only until 29 May 2002. The CEN committee TC 54 adopted EN 13445, "Unfired pressure vessels", as the matching standard in May 2002, by a CEN Technical Board document. The directive was recast as 2014/68/EU and has applied since 19 July 2016.
eur-lex.europa.eusingle-market-economy.ec.europa.eusirris.be
Credit
European Parliament and Council; CEN/TC 54
1999
Margin cut from 4 to 3.5
In the 1999 Addenda to its 1998 code, ASME lowered the design factor on a steel's tensile strength from 4.0 to 3.5 for Section I (power boilers) and Section VIII Division 1, which lets the same steel carry a higher allowable stress. The Hendrix Group's summary of an ASME Mechanical Engineering article credits better steelmaking, fracture toughness, welding and inspection; the factor of 1.5 on yield strength did not change.
LessonMargins written in 1915 were set for the steel and the inspection of 1915, and could be cut once both improved.
Credit
ASME Boiler and Pressure Vessel Committee
Watch for
An AI model for ASME codes
ASME and Articul8 AI say they are developing "the first GenAI model purpose-built for mechanical engineering standards", drawing on ASME's roughly 600 codes and standards, with access through software interfaces including MCP. The release gives no name, launch date or accuracy figures, and says only that unnamed industrial firms have given early validation.
Achieved whenthe model is generally available and an outside party publishes how often its answers to code questions and calculations are correct.
Claimed by
ASME and Articul8 AI, July 2026
Open
01
Code calculations, tested in public
An open, machine-readable set of pressure vessel design problems: shell and head thickness, nozzle reinforcement and flat covers, each with its inputs, the clause it follows, the expected answer and a tolerance. Use it to score AI models and calculation software against the same answers.
The briefCredit · unclaimed02
One test file for open calculators
A shared set of test cases that every open-source pressure vessel calculator can run, with each disagreement between tools traced to its cause and reported to the tool's authors.
The briefCredit · unclaimed
Open 01 · the brief
Code calculations, tested in public
The first to publish is credited on this line, and the deliverable moves from Open to Achieved.
What to build
An open, machine-readable set of pressure vessel design problems: shell and head thickness, nozzle reinforcement and flat covers, each with its inputs, the clause it follows, the expected answer and a tolerance. Use it to score AI models and calculation software against the same answers.
Why it is still open
ASME's own worked examples for Section VIII Division 1 are a paid manual (PTB-4, US$275 on ASME's page). Benchmarks of AI models on engineering calculations exist for other fields, such as TPS-CalcBench for thermal protection systems, but a search of arXiv in November 2026 for "pressure vessel" with "LLM" returned no papers.
Built with what exists
Python with the pint library for units; JSON Schema for the case format; open calculators such as calctoys and ASME-PVDE as reference answers; allowable stresses supplied as inputs so that no copyrighted tables are copied; AI models called through their public interfaces (the Note "Seven more flagged" covers an AI reviewer of long documents).
First step
Write the case format and 20 shell and head cases from published formulas, and run them through calctoys and ASME-PVDE.
Done looks like
At least 200 cases, each checked by two independent calculations, and a published table giving each AI model's share of answers within 1% of the expected value.
Open 02 · the brief
One test file for open calculators
The first to publish is credited on this line, and the deliverable moves from Open to Achieved.
What to build
A shared set of test cases that every open-source pressure vessel calculator can run, with each disagreement between tools traced to its cause and reported to the tool's authors.
Why it is still open
Several open calculators exist, among them thepvguy's calctoys in Python (last updated February 2023), ry4ngch's ASME-PVDE in Excel and VBA, and pxshaaa's wandstark. Each checks itself in its own way, and wandstark's verification notes say the allowable stress data from ASME's tables are not freely available and that only eight values have been independently confirmed.
Built with what exists
The calculators' own code; GitHub Actions to run every tool on every case; Python to compare results.
First step
Open an issue on each project proposing a common test case format, with five shell thickness cases attached.
Done looks like
One public test file run against at least three calculators, with every result that differs by more than 0.5% explained in an issue on the tool's page.