BRENNEN

Industries / Transport and vehicles / Shipbuilding and repair / Boat building

Repair and refit

Repair and refit is hauling boats out of the water, finding and fixing damage, renewing coatings and equipment, and, at the end, taking the boat apart for disposal.

4

Milestones achieved, from 2000 to 2018.

3

To watch for: announced, not yet confirmed outside.

2

Open deliverables. Nobody has shipped them.

The road

AchievedWatch forOpen

Achieved

  1. 2000

    Moisture meters put to test

    Surveyors, who inspect boats for buyers and insurers, press a handheld meter against a hull to look for water in the laminate. In 1999 Practical Sailor and the surveyor Jonathan Klopman tested five leading meters on fiberglass panels of known thickness laid over wet carpet, and then on hulls in boat yards. The depth each meter could read varied by brand, and the magazine concluded that "there is no correlation between the percentage of moisture indicated by the meter and the actual amount of moisture in the laminate." Klopman also surveyed 94 surveyors: most used a meter weekly, 33 percent described its working principle wrongly, and 63 percent were not sure how deep it read.

    Lessona meter reading compares one spot on a hull with another; it does not measure how much water is inside.

    practical-sailor.com

    Credit

    Practical Sailor; Jonathan Klopman, with Professional BoatBuilder magazine

  2. 2002

    A state removes derelicts

    A derelict boat is one left sunk, aground or abandoned. Washington State set up its Derelict Vessel Removal Program in 2002, and its Department of Natural Resources says the program has removed more than 1,205 abandoned or neglected vessels since. A turn-in program lets owners who can no longer look after a boat hand it over for disposal, and a 2020 law lifted a cap that had held spending on turn-ins to $200,000 every two years. Florida runs a similar turn-in program.

    Lessonby the department's account, taking a boat before it sinks costs considerably less than removing it afterward.

    dnr.wa.govmyfwc.com

    Credit

    Washington State Department of Natural Resources

  3. 2005

    Japan collects old fiberglass boats

    Fiberglass has been the main material for small boats in Japan since the early 1970s, by the account of the Ministry of Land, Infrastructure, Transport and Tourism (MLIT). Old hulls are strong, bulky and spread thinly across the country, local governments would not take them, and many were dumped illegally in the sea and in rivers. A government project from fiscal 2000 to 2003 worked out how to crush fiberglass hulls into fuel and raw material for cement kilns. In November 2005 the Japan Boating Industry Association, led by seven makers including Yamaha Motor, Suzuki and Toyota, began taking old boats in western Japan through registered dealers, and from fiscal 2008 the system ran in all 47 prefectures. Trade Only Today reported in 2019 that it had recycled more than 8,000 boats and sent only 12 or 13 percent of the material to landfill, but that owners pay for transport and recycling, so many choose cheaper dismantling that sends more to landfill.

    Lessona take-back scheme that charges the owner competes with every cheaper way to get rid of a boat.

    mlit.go.jpjapanfs.orgtradeonlytoday.com

    Credit

    Japan Boating Industry Association; MLIT

  4. 2018

    Old hulls unfit for dumping

    The countries that are party to the London Convention and Protocol, the treaties on dumping waste at sea, met at the International Maritime Organization from 5 to 9 November 2018 and reviewed a study they had commissioned from the consultant Simon Bray. It found fiberglass boats outliving the 30 to 50 years expected of them, "an abundance of unused, abandoned vessels with no sustainable disposal route," landfill as the main outlet, and no paying market for recycled fiberglass. The meeting endorsed a statement of concern that such boats "are not good candidates for disposal at sea, or appropriate for use as artificial reefs," since they may float or drift.

    imo.orgwwwcdn.imo.org

    Credit

    Parties to the London Convention and London Protocol; Simon Bray (AQASS Ltd)

Watch for

  1. Recycled fibers in new hulls

    Groupe Beneteau says a chain of six companies now collects offcuts from its plants, heats them without oxygen to separate the glass from the resin, and weaves the recovered glass into new fabric. It says a Lagoon catamaran shown in March 2026 was built with 80 percent recycled fibers and has "a robustness identical to new." Its Excess brand says an Excess 11 uses 45 percent recycled glass. The stated goal covers end-of-life boats as well as factory scrap; the recycler in the chain, Composite Recycling, signed an agreement with France's take-back body in December 2022 to treat glass from dismantled boats.

    Achieved whenan independent laboratory or classification society publishes strength tests of the recycled-fiber laminate, and fiber recovered from scrapped boats, not factory offcuts, goes into a hull.

    beneteau-group.compressmare.itrecyclermonbateau.fr

    Claimed by

    Groupe Beneteau, March 2026

  2. World guidance on old hulls

    The parties to the London Convention and Protocol have been drafting guidance on managing fiberglass boats at the end of their life and on alternatives to sinking them. Their 2024 meeting expected a final draft in 2025. The meeting of 27 to 31 October 2025 asked for new text that puts preventing disposal at sea ahead of costly monitoring, and sent the draft back to its scientific groups "for finalization in 2026."

    Achieved whenthe guidance is adopted and published by the International Maritime Organization.

    imo.orgimo.org

    Claimed by

    the governing bodies of the London Convention and Protocol, October 2025

  3. A robot that sands hulls

    Fabucbe, a company in Vittorio Veneto, Italy, lists a robot system called BOCAS for sanding, polishing and finishing boat hulls in shipyards and refit work, with dust extraction built in, and says it is "already available for pre-order." The listing gives no results from a yard.

    Achieved whena yard with no stake in the company reports hulls sanded by the system, with the area covered per hour and the dust measured.

    b2match.com

    Claimed by

    Fabucbe, September 2026

Open

  1. 01

    Wet core finders, scored

    A set of scrap sandwich panels, fiberglass skins over a balsa or foam core, with wet patches of known size and place hidden inside, and a blind test of the three tools surveyors use to find wet core: a moisture meter, a thermal camera and tapping with a small hammer.

    The brief
    Credit · unclaimed
  2. 02

    How long boats last

    A survival curve for boats: of those built in a given year, the share still registered 10, 20, 30 and 40 years later, by hull material and length, worked out from state registration files.

    The brief
    Credit · unclaimed

Open 01 · the brief

Wet core finders, scored

Credit · unclaimed

The first to publish is credited on this line, and the deliverable moves from Open to Achieved.

What to build

A set of scrap sandwich panels, fiberglass skins over a balsa or foam core, with wet patches of known size and place hidden inside, and a blind test of the three tools surveyors use to find wet core: a moisture meter, a thermal camera and tapping with a small hammer.

Why it is still open

Practical Sailor's 1999 test used solid fiberglass panels and found the meters' percent scales unrelated to the water present (see 2000 above). The surveyor Jack Allinson writes that reading a hull with a thermal camera "requires verification" by other methods and by cutting into the boat. A 2024 paper from Croatia shows a thermal camera finding blister damage in three case studies. A web search in November 2026 found no test that scores the three methods side by side on cored panels with known wet zones.

practical-sailor.comirinfo.orgapi.crossref.org

Built with what exists

Offcut cored panels from a boatyard, or small panels made with epoxy while wearing gloves in a ventilated space; water injected through holes in the back, then sealed; borrowed moisture meters of two brands; a phone thermal camera and a heat lamp; a phone microphone to record the taps. The panels are test pieces only, and the result is not a verdict on any boat.

  1. First step

    Make two panels with one known wet patch each and see whether a borrowed meter and a thermal camera can find them.

  2. Done looks like

    At least 20 panels holding 60 hidden wet patches and 60 dry control spots, each method tried blind by three people, and a published table of patches found, missed and falsely called, by patch size and skin thickness, with the panels cut open afterward to confirm.

Open 02 · the brief

How long boats last

Credit · unclaimed

The first to publish is credited on this line, and the deliverable moves from Open to Achieved.

What to build

A survival curve for boats: of those built in a given year, the share still registered 10, 20, 30 and 40 years later, by hull material and length, worked out from state registration files.

Why it is still open

Planning for scrapping rests on a trade estimate, quoted by NOAA, that 2 to 3 percent of US recreational boats, about 200,000, reach the end of their life each year. A 2023 report for NOAA by the RIMTA Foundation quotes another NMMA figure, 177,250 boats retired in 2016, or 1.5 percent of the fleet, without saying how it was counted. The US Coast Guard's yearly statistics list registered boats by year, length, propulsion and state. Washington Sea Grant publishes a yearly summary of one state's fleet that includes age and hull material, and calls it "not available anywhere else." A web search in November 2026 found no published survival curve for boats.

marinedebris.noaa.govecori.orguscgboating.orgwaseagrant.uw.edu

Built with what exists

State registration extracts by model year, length and hull material, with owners' details removed, obtained by public records request; Python with pandas and the lifelines survival-analysis library.

  1. First step

    Ask Washington or Florida for counts of registered boats by model year for two registration years ten years apart.

  2. Done looks like

    Curves for at least three states over at least ten registration years, the yearly retirement rate for fiberglass boats set beside the 2 to 3 percent estimate, and a stated allowance for boats that left the state instead of being scrapped, with code and summed tables published.