BRENNEN

Industries / Transport and vehicles / Shipbuilding and repair / Boat building

Engines and electrics

Engines and electrics is choosing and installing what drives the boat and powers what is aboard: the motor, its drive, the fuel or battery system, and the wires and data cables that tie them to the helm.

7

Milestones achieved, from 1909 to 2024.

3

To watch for: announced, not yet confirmed outside.

3

Open deliverables. Nobody has shipped them.

The road

AchievedWatch forOpen

Achieved

  1. 1909

    The outboard goes on sale

    An outboard is an engine, drive shaft and propeller in one unit that clamps to the back of a boat. Ole Evinrude built his first in Milwaukee in 1907 and, with his wife Bess, formed the Evinrude Motor Company in 1909 to make it. The motor made 1.5 horsepower at 1,000 rpm and weighed 62 pounds. Its layout, a horizontal cylinder, a vertical crankshaft and gears in a submerged lower unit, is still the usual one. The American Society of Mechanical Engineers (ASME) later named the 1909 model a national landmark. The landmark brochure, written with Evinrude's successor company, says outboards of some kind had existed for more than 40 years and calls his "the world's first truly commercially successful outboard motor". The Lemelson-MIT Program says others had experimented as early as 1896 and that Evinrude's was "the first commercial success".

    asme.orglemelson.mit.edu

    Credit

    Ole and Bess Evinrude

  2. 1959

    The sterndrive

    A sterndrive pairs an engine inside the hull with a propeller unit outside the transom, the flat back of the boat, that steers and tilts like an outboard. Volvo's own history says the American engineer Jim Wynne had the idea, found no taker in the United States and brought it to Volvo Penta, which showed the Aquamatic at the New York Boat Show in 1959 and sold 100 during the show. Volvo calls it "the world's first commercial 'inboard-outboard' or sterndrive motor". The engine sat protected in the hull and could be more powerful than an outboard, while the drive could be lifted in shallow water.

    volvogroup.com

    Credit

    Jim Wynne; Volvo Penta

  3. 1996

    Limits on outboard exhaust

    In October 1996 the US Environmental Protection Agency (EPA) set its first exhaust limits for gasoline boat engines, covering outboards, personal watercraft and jet boats. EPA wrote that these engines were mostly two-strokes, a simple design that "emits high rates" of hydrocarbons, which are unburned fuel. The limits tightened each model year from 1998 to 2006, when each maker's engines had to average 75 percent less hydrocarbon than unregulated ones. EPA named four-stroke engines and two-strokes with direct fuel injection among the designs it expected makers to use. A second rule in October 2008 tightened outboard limits from 2010, set the first limits for sterndrive and inboard engines (5.0 grams of hydrocarbons plus nitrogen oxides per kilowatt-hour), and limited fuel vapor escaping from tanks and hoses.

    govinfo.govnepis.epa.gov

    Credit

    US EPA

  4. 2000

    Generator exhaust poisons swimmers

    In 2000 the US National Park Service asked the National Institute for Occupational Safety and Health (NIOSH) and the Coast Guard to investigate carbon monoxide (CO) poisonings and deaths on houseboats at Lake Powell, on the Arizona-Utah border. Gasoline generators vented their exhaust at the stern. Around the swim platform NIOSH measured CO at or above 1,200 parts per million, the level it calls immediately dangerous to life. NIOSH counted 309 houseboat CO poisonings in the United States from 1990 to April 2008, 26 of them fatal, and more than 800 poisonings across recreational boating. It then tested fixes with builders: an exhaust stack ending 9 feet above the upper deck cut CO in occupied areas by as much as 99 percent, and two generator makers, Westerbeke and Kohler, brought out low-CO generators with fuel injection and a catalyst. The American Boat and Yacht Council (ABYC), which writes US boatbuilding standards, added exhaust stacks to its generator standard.

    Lessonwhere an exhaust outlet points is a design decision, and it decides who breathes the gas.

    archive.cdc.govpmc.ncbi.nlm.nih.gov

    Credit

    NIOSH (Ronald Hall, G. Scott Earnest and colleagues); US Coast Guard; National Park Service

  5. 2001

    One network for instruments

    NMEA 2000 is a standard that lets engines, sensors and displays from different makers share data over one cable. It is built on CAN (Controller Area Network), the wiring and message scheme used in cars and trucks. The National Marine Electronics Association (NMEA) began work on it in 1994 and released version 1.000 in 2001, by CSS Electronics' timeline; it became the international standard IEC 61162-3 in 2008. A backbone cable runs through the boat and each device joins it by a short drop cable. The network has no central controller, and NMEA requires every product that reads or sends its messages to be certified.

    nmea.orgcsselectronics.comkvaser.com

    Credit

    NMEA Standards Committee

  6. 2005

    Pod drives and joysticks

    Volvo Penta launched its Inboard Performance System (IPS) in 2005. Each engine turns a steerable drive unit, called a pod, under the hull, with two propellers that face forward and spin in opposite directions, so there are no rudders or long propeller shafts. A joystick followed in 2006: the skipper pushes it the way the boat should move and electronics steer each pod. Volvo Penta claims 30 percent lower fuel use and 20 percent higher top speed than shaft-driven inboards. Jens Bering of Volvo Penta wrote in 2019 that more than 24,000 units had gone to 540 builders. Other engine makers now sell joystick control.

    volvogroup.comtradeonlytoday.com

    Credit

    Volvo Penta

  7. 2024

    An electric ferry on foils

    Hydrofoils are underwater wings that lift a hull clear of the water at speed, which cuts drag. Candela's P-12, a battery-electric hydrofoil boat built in Stockholm, entered the city's public transport in autumn 2024 on a pilot route from Ekerö to City Hall, run by Candela, the Swedish Transport Administration (Trafikverket) and Region Stockholm. The EU Urban Mobility Observatory reported in May 2025 that the boat charges at an ordinary car fast charger. Trafikverket's final report on the pilot, dated 30 January 2026, gives its own measurements: the shortest trip took 30 minutes, against 45 to 55 minutes for conventional ferries on the route; energy use was 0.24 kWh per passenger-kilometer, 66 percent less than diesel; and the wake was 0.13 m high at 43 m from the boat at 24 knots, about half that of a comparable diesel boat. It puts the cut in carbon dioxide at 94 percent against diesel, using Sweden's low-carbon electricity, and counts 22.5 percent more riders on the route during the trial.

    diva-portal.orgurban-mobility-observatory.transport.ec.europa.eu

    Credit

    Candela; Trafikverket; Region Stockholm

Watch for

  1. Boats that dock themselves

    Simrad, a Brunswick brand, says its AutoCaptain system docks and undocks a boat without the skipper steering, using cameras around the hull and Mercury engines, including in marinas the boat has not visited before. It is sold as an option on the Boston Whaler 405 Conquest. BoatUS, which rode along on a demonstration, reports six stereo cameras, a working range of about 200 feet and a price of about $120,000, and notes that Simrad lists limits: the system is not designed to detect shallow water, submerged objects or swimmers.

    Achieved whenan outside tester publishes a count of docking attempts in wind and current, with failures and skipper takeovers included.

    panbo.comboatus.com

    Claimed by

    Simrad (Brunswick Corporation), October 2025

  2. Docking help for refits

    Avikus, the autonomous navigation arm of HD Hyundai, launched NeuBoat Control, which it calls "the world's first semi-autonomous docking system for recreational boats". On a boat with joystick control, the user picks bow, stern, port or starboard docking and the system works out distances and the push of wind and current. Avikus offers it to builders and for dealer refits.

    Achieved whenan independent test on boats in service reports how often it docks without help.

    boatingindustry.ca

    Claimed by

    Avikus, February 2026

  3. Long trips on car chargers

    Candela says a P-12 traveled 160 nautical miles from Gothenburg, Sweden, to Oslo, Norway, over three days, which it calls the longest journey by an electric passenger ship. The boat charged from car fast chargers and a battery towed by a pickup truck, and Candela puts the electricity cost at just over €200.

    Achieved whenan outside body checks the trip logs, or an operator runs a long scheduled route and reports its energy use.

    candela.com

    Claimed by

    Candela, February 2026

Open

  1. 01

    Fault library for boat networks

    a public set of recordings from a bench NMEA 2000 network with known wiring faults (a missing terminator, an extra terminator, low supply voltage, two devices claiming one address, a drop cable that is too long, a high-resistance connector), and a small program that names the fault from a recording.

    The brief
    Credit · unclaimed
  2. 02

    Measured range for electric boats

    a shared test method and a public table of energy use for electric boats, in kilowatt-hours per nautical mile at set speeds, measured the same way on every boat.

    The brief
    Credit · unclaimed
  3. 03

    Chart the two-stroke's exit

    one tidy public table of EPA's certification records for gasoline boat engines from 1998 to now, with maker, model year, power, engine type, fuel system and certified emissions for each engine family, and charts that count, year by year, how many certified outboard families were carbureted two-strokes, direct-injection two-strokes and four-strokes.

    The brief
    Credit · unclaimed

Open 01 · the brief

Fault library for boat networks

Credit · unclaimed

The first to publish is credited on this line, and the deliverable moves from Open to Achieved.

What to build

a public set of recordings from a bench NMEA 2000 network with known wiring faults (a missing terminator, an extra terminator, low supply voltage, two devices claiming one address, a drop cable that is too long, a high-resistance connector), and a small program that names the fault from a recording.

Why it is still open

The standard itself is sold, not published; the open-source canboat project decodes its messages only because volunteers worked them out by watching networks. Public CAN recordings exist for cars, such as the CrySyS set of attack logs, and a 2019 paper used NMEA 2000 battery sensors to predict battery failures, not bus faults. Researchers at the University of Oxford built CANDID, a system that detects attacks on J1939 and NMEA 2000 networks from message timing and content; it looks for intruders, not wiring faults, and the abstract mentions no released recordings. Searches of the web, GitHub and Hugging Face in November 2026 found no public set of NMEA 2000 recordings with labeled wiring faults.

github.compmc.ncbi.nlm.nih.govapi.crossref.orgcs.ox.ac.uk

Built with what exists

an NMEA 2000 starter kit (backbone cable, T-connectors, two terminators), three or four low-cost devices, a 12-volt bench supply, a USB CAN adapter or a Raspberry Pi with a CAN board, python-can, canboat and scikit-learn. The bench runs at 12 volts and never goes aboard.

  1. First step

    build a four-device bench, record ten minutes with and without one terminator, and compare the error frames.

  2. Done looks like

    500 labeled recordings covering six fault types and the healthy network, made on two benches built from different parts; a classifier trained on the first bench and scored on the second, with its accuracy per fault published; data and code under an open license.

Open 02 · the brief

Measured range for electric boats

Credit · unclaimed

The first to publish is credited on this line, and the deliverable moves from Open to Achieved.

What to build

a shared test method and a public table of energy use for electric boats, in kilowatt-hours per nautical mile at set speeds, measured the same way on every boat.

Why it is still open

Most range figures come from the makers. BoatTEST's list of 20 electric boats gives ranges "according to public information" or as "the builder says". Single boats have been measured, each its own way. Boating magazine's test of the Rock Proof ePro 1760R bass boat got 13.5 miles at 25.1 mph from 20 kWh of usable battery, with two anglers aboard. Bureau Veritas certified that a Lasai 22GL, a solar-electric boat, covered 109 nautical miles on one charge in July 2025, running laps of a 1.62-nautical-mile course near Bilbao at about 6 knots for 18.5 hours. A web search in November 2026 found no table of several boats measured by one method at the same speeds.

boattest.comboatingmag.comcorresponsables.com

Built with what exists

the boat's own NMEA 2000 data (battery voltage, current and speed over ground), read through a gateway with the open-source Signal K server on a Raspberry Pi; a GPS track; a one-page run method. Nothing is connected to the battery itself, and the boat's usual operator drives.

  1. First step

    write the run method and log one boat with its owner at a local club.

  2. Done looks like

    20 boats from at least five makers, each with energy per nautical mile at three speeds from runs in both directions over a measured course, with wind and load noted, raw logs published, and the maker's claimed range beside the measured one.

Open 03 · the brief

Chart the two-stroke's exit

Credit · unclaimed

The first to publish is credited on this line, and the deliverable moves from Open to Achieved.

What to build

one tidy public table of EPA's certification records for gasoline boat engines from 1998 to now, with maker, model year, power, engine type, fuel system and certified emissions for each engine family, and charts that count, year by year, how many certified outboard families were carbureted two-strokes, direct-injection two-strokes and four-strokes.

Why it is still open

EPA publishes the records as two spreadsheets with different layouts: an archive for 1998 to 2011 with about 2,900 engine-family rows and separate sheets for models and parts, and a file for 2011 to the present with about 6,000 rows. Searches of GitHub and Crossref in November 2026 found engine test papers but no combined table and no year-by-year count.

epa.gov

Built with what exists

EPA's two files, Python with pandas and openpyxl, and an AI model to propose how the old file's technology codes map to the new file's columns, checked by hand.

  1. First step

    load both files, list their columns, and line up the model year 2011 rows that both carry.

  2. Done looks like

    one CSV file covering every model year from 1998, a written column mapping, 50 randomly chosen rows checked by hand against EPA's files, and the charts, all published with the code.