BRENNEN

Industries / Consumer goods / Baby products

Sleep products

Sleep products are the cribs (cots), bassinets, play yards, mattresses, bedside sleepers, baby boxes, swaddles and sleep sacks that a baby sleeps in or on, and the rules and tests that decide which designs may be sold.

7

Milestones achieved, from 1938 to 2026.

1

To watch for: announced, not yet confirmed outside.

2

Open deliverables. Nobody has shipped them.

The road

AchievedWatch forOpen

Achieved

  1. 1938

    A cardboard first bed

    Under Finland's Maternity Grants Act of 1937, the first maternity grants were paid in 1938, at first only to low-income mothers, as cash, as goods (the maternity package) or both; about two-thirds of new mothers received one that year. In 1949 the grant was opened to all mothers. Kela, which has run the scheme since 1994, awards about 50,000 grants a year, about 30,000 of them as the package. Kela's 2026 box is corrugated cardboard, 70 × 42.8 × 27 cm, and Kela says it "can be used as the baby's first bed together with the mattress."

    kela.fikela.fi

    Credit

    Government of Finland (Maternity Grants Act, 1937); Kela

  2. 1973

    Gaps between slats capped

    The first US mandatory rule for full-size cribs (16 CFR 1508), published on 21 November 1973, held the gap between slats, spindles and corner posts to no more than 6 cm (2 3/8 inches), so that a baby's body cannot slip through, and set the top of the side at least 66 cm (26 inches) above the mattress support. A rule for smaller cribs followed in 1976. In 1995 the CPSC estimated that deaths in cribs had fallen from 150 to 200 a year to about 50.

    Lessonmost of the deaths the CPSC still saw in 1995 were in cribs that were previously owned, so a rule for new cribs leaves old ones in homes for years.

    govinfo.govcpsc.gov

    Credit

    US Consumer Product Safety Commission (CPSC)

  3. 2011

    Drop-side cribs end

    A drop-side crib has a front side that slides down so a parent can lift the baby out. Since 2007 the CPSC had announced 46 recalls covering more than 11 million cribs. Between November 2007 and April 2010 it received reports of 147 deaths associated with full-size cribs; 35 were put down to structural problems, and 18 of those to drop-side failures. New rules (16 CFR 1219 and 1220), in force from 28 June 2011, made the ASTM standards F1169-10 and F406-10a mandatory: they prohibit traditional drop-sides and add tests such as an 80 lbf (about 356 newtons) strength test for slats. Child care centers and hotels had until 28 December 2012 to replace their cribs.

    Lessonalmost all the structural failures, whether parts detached, came loose or broke, opened a gap in which a baby was trapped, so a crib has to hold together in years of use, not only measure right when new.

    federalregister.gov

    Credit

    CPSC, under section 104 of the Consumer Product Safety Improvement Act of 2008; ASTM International

  4. 2022

    Inclined sleepers banned

    Since the "Back to Sleep" campaign of the early 1990s, the advice had been for babies to sleep flat on their backs. Fisher-Price's Rock 'n Play Sleeper, launched in October 2009 and by a House of Representatives committee's account the first inclined sleeper on the market, held babies at an angle for overnight sleep; the company tested it on 62 infants before launch, and 4.7 million were sold before the recall in April 2019. A study paid for by the CPSC and led by Erin Mannen of the University of Arkansas for Medical Sciences concluded in September 2019 that none of the inclined sleep products it evaluated were safe for infant sleep. The CPSC's infant sleep products rule (16 CFR 1236), in force from 23 June 2022, requires any sleep product for babies up to 5 months to have a sleep surface no more than 10 degrees from horizontal; its 2019 proposal had counted 59 deaths in inclined sleep products. The Safe Sleep for Babies Act, signed on 16 May 2022, banned inclined sleepers above 10 degrees and padded crib bumpers outright, and in 2024 the CPSC applied the 10-degree limit to infant support cushions such as loungers, after counting 79 deaths from 2010 to 2022.

    Lessonthe CPSC proposed a 5-degree limit for infant sleep products in 2010 and then left inclined sleepers out, so a design that went against flat-sleep advice stayed on sale for nearly ten years.

    docs.house.govgovinfo.govgovinfo.govgovinfo.gov

    Credit

    CPSC; Erin Mannen and colleagues; US Congress

  5. 2022

    A firmness test from Australia

    The CPSC's crib mattress rule (16 CFR 1241), in force from 15 August 2022, made the ASTM F2933-21 standard mandatory for crib mattresses, including aftermarket mattresses sold to replace the one that came with a play yard or small crib. It added a firmness test taken from the Australian and New Zealand standard AS/NZS 8811.1:2013: a rigid fixture weighing 5,200 g with a round base 203 mm across is set on the mattress, and if a flat bar 15 mm above the base touches the mattress at all, the mattress fails. The CPSC counted 494 reports, including 139 deaths, associated with crib mattresses from January 2010 to April 2021. Australia's own mandatory standard for infant sleep products, enforced from 19 January 2026, also requires a firm sleep surface and allows an incline of no more than 7 degrees.

    govinfo.govgovinfo.govproductsafety.gov.au

    Credit

    CPSC; ASTM International; the joint Australian and New Zealand standard AS/NZS 8811.1; Australian Competition and Consumer Commission (ACCC)

  6. 2023

    A bassinet becomes a device

    On 30 March 2023 the US Food and Drug Administration (FDA) granted Happiest Baby's De Novo request, the route for a new kind of medical device with no existing equivalent, for its SNOO Smart Sleeper: a bassinet that rocks and plays white noise, more strongly when the baby cries, with a sleep sack whose fabric wings clip to the bassinet to keep the baby on its back. The FDA created a new device type for it, the "infant supine sleep system" (21 CFR 880.5690), for babies from birth to 6 months who cannot yet roll over. The company's data showed about 98.7% of 1,012 users on their backs, but the FDA wrote that the SNOO "has not directly demonstrated a reduction in the incidence of SIDS/SUID" (sudden infant death syndrome or sudden unexpected infant death) and required a further study.

    Lessona sleep product authorized as a medical device then has to meet device rules, and in June 2026 the FDA warned the company over how it grouped complaints and over sleep sack sizes sold without the premarket submission the agency said they needed.

    accessdata.fda.govaccessdata.fda.govfda.gov

    Credit

    Happiest Baby, Inc.; FDA

  7. 2026

    Europe bars weighted sleep bags

    In 2010 the European Commission set the safety requirements that European standards must meet for cot mattresses, cot bumpers, suspended baby beds, children's duvets and children's sleep bags, saying more babies die in incidents with cots and cot-related products than with any other child-care product. The sleep bag standard that followed, EN 16781:2018, was revised in 2026. The new edition states that weighted sleep bags are not permitted and caps insulation at 4 tog for bags without sleeves and 3 tog with sleeves (tog is a unit of thermal resistance; 1 tog is 0.1 m²·K/W), and CEN members must adopt it as a national standard by March 2027. In the US, the American Academy of Pediatrics (AAP) called weighted swaddles "not safe", and after CPSC Commissioner Richard Trumka wrote to retailers in April 2024, Target, Walmart, Nordstrom and Babylist said they would stop selling weighted infant sleep products and Amazon changed its seller policy.

    legislation.gov.ukintertek.comhppr.orgsleepreviewmag.com

    Credit

    European Commission; CEN (European Committee for Standardization); AAP; Commissioner Richard Trumka Jr. (CPSC)

Watch for

  1. Weighted sack warning sent back

    The CPSC's safe sleep guidance says that "parents and caregivers should not use weighted blankets or swaddles." Dreamland Baby, a maker of weighted sleep sacks, sued in November 2024, claiming the warning is unjustified. In an opinion dated 25 September 2026, the US District Court for the District of Columbia found that the CPSC had not given the "satisfactory explanation" that US administrative law requires, both for publishing the statement and for refusing to retract it, and sent the matter back to the agency to investigate and explain, according to Dreamland's lawyers.

    Achieved whenthe CPSC publishes the evidence and reasons behind its warning and the court accepts them, or the agency withdraws or narrows the warning.

    nclalegal.orgmanilatimes.net

    Claimed by

    Dreamland Baby Co. and its lawyers, the New Civil Liberties Alliance, September 2026

Open

  1. 01

    An open mattress firmness tester

    A low-cost copy of the US crib mattress firmness fixture (a rigid 203 mm round base weighing 5,200 g ± 20 g, a flat bar 12 mm wide set 15 mm above the base, and a bullseye level), released as open drawings and a parts list. With it, a free public table of firmness results for at least 40 crib mattresses and aftermarket play yard and mini-crib mattresses on sale in the US, including cheap marketplace listings, each tested at the points the rule sets on each side that could face up. No child is involved; the fixture stands in for the head.

    The brief
    Credit · unclaimed
  2. 02

    Weighted sleep sacks on manikins

    A public bench dataset on how weighted infant sleep sacks and swaddles load a baby's chest, measured only on a manikin about the size of a 3-month-old. For each product it gives the total mass and the mass of the weighted panel, a pressure map over the chest and belly, and the extra force a servo-driven "breathing" chest plate needs to rise 5 mm under the product. Each weighted product is compared with an unweighted sack of the same size, with the manikin on its back and on its side.

    The brief
    Credit · unclaimed

Open 01 · the brief

An open mattress firmness tester

Credit · unclaimed

The first to publish is credited on this line, and the deliverable moves from Open to Achieved.

What to build

A low-cost copy of the US crib mattress firmness fixture (a rigid 203 mm round base weighing 5,200 g ± 20 g, a flat bar 12 mm wide set 15 mm above the base, and a bullseye level), released as open drawings and a parts list. With it, a free public table of firmness results for at least 40 crib mattresses and aftermarket play yard and mini-crib mattresses on sale in the US, including cheap marketplace listings, each tested at the points the rule sets on each side that could face up. No child is involved; the fixture stands in for the head.

Why it is still open

The fixture and procedure are printed in the rule's Federal Register text, so no paid standard is needed, but testing is done in paid labs: the CPSC put the firmness test at about USD 250 per model, and its own staff tested 11 full-size mattresses for the rule. Partial work exists elsewhere. CHOICE in Australia tests cot mattresses to AS/NZS 8811.1 and rates nine. Hong Kong's Consumer Council tested 8 models to the European standard EN 16890 in 2019 and found 3 that fell short on firmness. Gillani, Lowell and Quinlan (2021) built a softness gauge with a 2.5 lb weight and measured 17 surfaces, sharing data only on request, and Nelson Fumo patented a home tester that uses a bottle of soda as the weight. Searches found no open design of the regulation fixture and no free public table of US results.

govinfo.govchoice.com.auconsumer.org.hkpmc.ncbi.nlm.nih.govpatents.google.com

Built with what exists

A waterjet-cut or turned aluminium disk with steel shot to trim the mass; a calibrated scale and gauge blocks to check mass and bar height; spring steel for the bar; a 100% cotton fitted sheet, as the rule requires; a simple contact circuit on an Arduino and a Raspberry Pi camera to record each placement; Claude Fable 5.2 to help lay out the contact-sensing board (see the Note "Three working devices"); Browser Use 1.0 to collect listings, sellers and prices when choosing the sample (see the Note "Deleting 80% to start over"); Python and a public Git repository.

  1. First step

    Build one fixture from the Federal Register text, check its mass and bar height, and test five mattresses bought this month, two of them aftermarket play yard mattresses from an online marketplace.

  2. Done looks like

    Drawings, parts list and costs published under an open licence; the fixture's mass within 5,200 ± 20 g and its bar height within 15 ± 0.2 mm, checked by two people; the same pass or fail as an accredited lab on at least 10 mattresses tested by both; a public table of at least 40 mattresses with price, seller, purchase date and result at every test point, with videos.

Open 02 · the brief

Weighted sleep sacks on manikins

Credit · unclaimed

The first to publish is credited on this line, and the deliverable moves from Open to Achieved.

What to build

A public bench dataset on how weighted infant sleep sacks and swaddles load a baby's chest, measured only on a manikin about the size of a 3-month-old. For each product it gives the total mass and the mass of the weighted panel, a pressure map over the chest and belly, and the extra force a servo-driven "breathing" chest plate needs to rise 5 mm under the product. Each weighted product is compared with an unweighted sack of the same size, with the manikin on its back and on its side.

Why it is still open

The measurements on babies are few, small and old. NPR described a 2020 study of 16 infants in neonatal intensive care under a 1-pound weighted blanket, and a five-infant test commissioned by the maker Nested Bean that placed about 1, 3 and 9.5 ounces on the chest for two minutes each, whose researchers wrote that the heavier weights "may increase potential hazard and subsequent risk." Products differ widely: by NPR's account Nested Bean's carry about 1 to 2 ounces of beads on the chest and Dreamland's 0.8 to 1.5 pounds. A US court has now asked the CPSC to explain its warning, and Europe's EN 16781:2026 excludes weighted bags, yet searches found no newer study and no published bench measurements of the chest load these products add.

hppr.orgnclalegal.orgintertek.com

Built with what exists

An infant CPR training manikin or a 3D-printed torso fitted with a servo-driven chest plate; a load cell with an HX711 amplifier on an Arduino; a thin-film pressure-mapping mat (a commercial one such as Tekscan, or a home-made grid of Velostat, a pressure-sensitive plastic sheet); Python for analysis; Claude Fable 5.2 to help design the sensor board (see the Note "Three working devices").

  1. First step

    Fit a load cell under the chest plate of one manikin and measure two weighted and two unweighted sacks of the same size.

  2. Done looks like

    At least 8 weighted and 8 unweighted products, each measured five times, with repeat measurements within 5% of each other; a table of each product's added load over the chest in grams, its peak pressure in kilopascals and the extra force needed to lift the chest; drawings, raw data and code published.