BRENNEN

Industries / Industrial equipment and services / Industrial services / Welding and fabrication

Manual welding

Manual welding is joining metal by hand with heat, from a gas flame or an electric arc, with the welder guiding a rod, torch or wire gun along the joint.

7

Milestones achieved, from 1885 to 2026.

1

To watch for: announced, not yet confirmed outside.

2

Open deliverables. Nobody has shipped them.

The road

AchievedWatch forOpen

Achieved

  1. 1885

    Welding with a carbon arc

    An electric arc is a spark held steady across a gap, hot enough to melt steel. Nikolay Benardos and Stanisław Olszewski joined metal with an arc drawn between a hand-held carbon rod and the workpiece, which melted only the spot under the arc. They called the method "Elektrogefest" and patented it in France in 1885 (patent no. 171596, dated 10 October 1885), then in other countries; their US patent, filed on 3 December 1885 and granted on 17 May 1887, lists joining metals "end to end or placed one on top of the other", boring holes and cutting. A 2019 history in the bulletin of Poland's Welding Institute says the two presented the method in 1881 and that "it was then that the history of arc welding started". The same article calls Auguste de Méritens's earlier arc welding of lead battery plates "the first fully documented application" of the arc for welding, and names an 1866 British patent by Henry Wilde as the first concerning arc welding.

    patents.google.combulletin.is.gliwice.pl

    Credit

    Nikolay Benardos and Stanisław Olszewski, both of St. Petersburg

  2. 1941

    A torch for magnesium

    Magnesium alloys, used in aircraft, catch fire when heated in air, so they could not be gas welded. Russell Meredith of Northrop Aircraft built a torch that struck an arc from a tungsten electrode, which does not melt away, inside a blanket of helium, an inert gas that does not react with hot metal; the welder fed filler rod into the arc by hand. He applied for the patent on 4 January 1941 and it was granted on 24 February 1942. The method, later called TIG (tungsten inert gas) welding, built on helium and argon shielding that H. Hobart and P. K. Devers of General Electric had patented (US patents granted in 1930). Northrop sold the patent rights and the "Heliarc" name to Linde in 1942, and Linde extended the method to aluminum, stainless steel, copper and nickel alloys.

    patents.google.combulletin.is.gliwice.pl

    Credit

    Russell Meredith, Northrop Aircraft; Linde

  3. 1949

    Wire fed through the gun

    In stick welding the welder holds a short coated rod that burns down and must be replaced. On 21 January 1949 Albert Muller, Glenn J. Gibson and Nelson E. Anderson of the Air Reduction Company applied for a patent on gas-shielded metal arc welding with a hand-held gun: a bare wire, fed automatically at a constant speed of at least 100 inches per minute, carries the current and melts into the joint under a shield of argon or helium. The patent, granted on 18 April 1950, describes the semi-automatic process now called MIG (metal inert gas) welding, or MAG when the gas is active, such as carbon dioxide.

    patents.google.com

    Credit

    Albert Muller, Glenn J. Gibson and Nelson E. Anderson, Air Reduction Company

  4. 1981

    A lens that darkens itself

    A welder must look through a dark filter to watch the arc but cannot see the joint through it before the arc starts, so welders flipped their helmets down at the last moment. In 1981 the Swedish company Hörnell, now part of 3M, sold its first auto-darkening filter, a liquid crystal lens that turns dark when sensors see the arc, according to The Fabricator. Occupational Health & Safety magazine says Speedglas founder Åke Hörnell built the prototype in 1976.

    LessonEarly filters behaved erratically, fooled by pulsing TIG arcs or bright outside light, and in 2005 the magazine reported that most welders still used fixed-shade lenses, so a safety device spread only once it was reliable.

    thefabricator.comohsonline.com

    Credit

    Åke Hörnell, Hörnell (Speedglas)

  5. 1994

    Earthquake cracks the welds

    After the 1994 Northridge earthquake, cracking was found in the welded beam-to-column joints of steel frames in more than 100 buildings in the Los Angeles area. A study by the US National Institute of Standards and Technology (NIST) and Lehigh University of 16 fractured joints from five buildings found that every fracture started at the root of the weld, at a flaw where the weld had not fused, next to the notch left by the backing bar, a steel strip left under the joint. The weld metal in every case came from a flux-cored wire classed E70T-4 and had very poor fracture toughness, its resistance to cracking from a flaw. The 1997 seismic provisions of the American Institute of Steel Construction then required filler metal rated for a toughness of 20 ft-lb in a Charpy V-notch impact test at −20 °F, and FEMA's later guidelines (FEMA-350) recommend removing backing bars from these joints because a backing bar left in place hides flaws at the weld root from inspectors.

    LessonA weld that must stretch in an earthquake needs filler metal with a stated toughness, and joint details that let inspectors see the root.

    nehrpsearch.nist.govnehrp.gov

    Credit

    a failure; investigated by Eric Kaufmann and John Fisher (Lehigh University), Roger Di Julio Jr. and John Gross (NIST)

  6. 2017

    Welding fume causes cancer

    A working group of the International Agency for Research on Cancer (IARC), the World Health Organization's cancer agency, met in Lyon from 21 to 28 March 2017 and classed welding fumes as carcinogenic to humans (Group 1), finding that they cause lung cancer. It also classed ultraviolet light from welding as carcinogenic, a cause of melanoma of the eye. IARC estimates that 11 million workers worldwide have the job title of welder and about 110 million more probably meet welding exposures. In February 2019 Britain's Health and Safety Executive told employers it would no longer accept any welding, however short, done without suitable exposure controls, and that general ventilation alone does not control the fume indoors.

    publications.iarc.who.intpublications.iarc.who.inthse.gov.uk

    Credit

    IARC Monographs Working Group (Volume 118); UK Health and Safety Executive

  7. 2026

    EU law covers welding fume

    The European Commission proposed on 18 July 2025 to bring welding fumes within the EU directive on carcinogens, mutagens and reprotoxic substances at work, noting that the fumes can contain chromium, nickel and cadmium compounds. The European Parliament approved the amended directive on 6 October 2026 by 499 votes to 49, the Council adopted it on 19 October, and it was published in the Official Journal on 30 October 2026. It sets no single limit for welding fume; the Parliament's summary says the Commission should assess the need for further limits on substances in the fume.

    employment-social-affairs.ec.europa.euoeil.europarl.europa.euoeil.europarl.europa.eu

    Credit

    European Commission, European Parliament and Council of the EU

Watch for

  1. Handheld lasers in code work

    A handheld laser welder is a fiber laser fed through a gun the welder holds like a torch. At FABTECH, North America's largest metal fabrication show, IPG Photonics and the Handheld Laser Institute presented a framework for "code-worthy" handheld laser welds on 21 October 2026, covering welding procedure specifications, procedure qualification records, mechanical testing and "alignment with AWS and other code requirements". The American Welding Society (AWS) wrote in December 2024 that manufacturers "currently lack AWS specifications for handheld laser beam welding", that developing them "is expected to last several years", and that its general qualification standard, B2.1, may be used to self-qualify a weld in the meantime.

    Achieved whenAWS, ISO or another code body publishes rules that cover handheld laser welding, or a code authority accepts work qualified under them.

    cdn.fabtechexpo.comaws.org

    Claimed by

    Daniel Earley (IPG Photonics) and Rex Alexandre (Handheld Laser Institute), October 2026

Open

  1. 01

    Fume sensor inside the helmet

    A small logger clipped inside a welding helmet, near the mouth, that records particle readings every second while the welder works, and a public data set that pairs its readings with filter samples worn beside it during stick, MIG, flux-cored and TIG welding at a welding school.

    The brief
    Credit · unclaimed
  2. 02

    Public tests of laser welds

    A public record of procedure qualification tests for handheld laser welds: butt and fillet joints in 1.5 mm and 3 mm stainless and carbon steel, each with the machine settings, bend and tensile test results, and photos of cut, polished and etched cross sections, laid out like the procedure qualification record (PQR) that AWS B2.1 asks for and released under an open license.

    The brief
    Credit · unclaimed

Open 01 · the brief

Fume sensor inside the helmet

Credit · unclaimed

The first to publish is credited on this line, and the deliverable moves from Open to Achieved.

What to build

A small logger clipped inside a welding helmet, near the mouth, that records particle readings every second while the welder works, and a public data set that pairs its readings with filter samples worn beside it during stick, MIG, flux-cored and TIG welding at a welding school.

Why it is still open

Welding fume is now a known cause of lung cancer, and the standard way to measure a welder's exposure, pumping air through a filter and weighing it, gives one average per shift and nothing about which task caused it. Cheap particle sensors tracked welding fume well in a University of Iowa test chamber only after calibration against reference instruments, and the authors found that "aerosol type strongly influenced sensor response". One search in November 2026 found chamber tests like this but no field test of a cheap sensor worn inside a welding helmet.

pmc.ncbi.nlm.nih.govhse.gov.uk

Built with what exists

A Sensirion SPS30 or Plantower PMS5003 particle sensor; an ESP32 microcontroller logging to a memory card; a 3D-printed mount behind the lens; rented personal sampling pumps with 37 mm filter cassettes, weighed by an accredited industrial hygiene lab; Python for calibration.

  1. First step

    Build one logger and run it beside a rented filter sampler during five MIG practice sessions at a welding school, then plot the two results.

  2. Done looks like

    At least 100 full welding sessions across the four processes, each with a sensor log and a weighed filter from the same position; a calibration for each process; and, on sessions held back from calibration, the share whose sensor average falls within 25% of the filter result, published with the design and data under an open license.

Open 02 · the brief

Public tests of laser welds

Credit · unclaimed

The first to publish is credited on this line, and the deliverable moves from Open to Achieved.

What to build

A public record of procedure qualification tests for handheld laser welds: butt and fillet joints in 1.5 mm and 3 mm stainless and carbon steel, each with the machine settings, bend and tensile test results, and photos of cut, polished and etched cross sections, laid out like the procedure qualification record (PQR) that AWS B2.1 asks for and released under an open license.

Why it is still open

AWS says there are no AWS specifications for handheld laser beam welding yet and that writing them will take several years; its D17 committee has begun adding handheld units to its aerospace welding specification, D17.1. Until then each shop runs and pays for its own qualification tests and keeps the results. The October 2026 FABTECH session teaches a framework for such tests but publishes no results. Searches in November 2026 found makers' claims but no public set of test results.

aws.orgcdn.fabtechexpo.com

Built with what exists

A handheld fiber laser welder such as IPG LightWELD or Miller OptX at a school or shop that has a laser safety officer and a laser-safe booth, who does all the welding; the school's tensile tester and bend jig; etchant and a digital microscope for cross sections; Zenodo for the data.

  1. First step

    Ask a shop that owns a handheld laser welder to weld five 1.5 mm stainless butt joints, and have a welding school bend-test them.

  2. Done looks like

    At least 40 test coupons across the eight joint, metal and thickness combinations, each tested and photographed, with settings and results published and each record reviewed by an AWS Certified Welding Inspector.