Industries / Technology / Telecommunications
Field work on towers and lines
Field work is the hands-on building and upkeep of the physical network: climbing towers, stringing and lashing cable on poles, digging trenches and splicing fiber.
4
Milestones achieved, from 1978 to 2019.
2
To watch for: announced, not yet confirmed outside.
2
Open deliverables. Nobody has shipped them.
The road
AchievedWatch forOpen
Achieved
1978
Fusing glass in the field
Fusion splicing joins two optical fibers by melting their ends together with an electric arc. Ingenium, Canada's national science and technology museum, holds a Northern Telecom S-25 dated 1978 and describes it as the first fusion splicer Bell-Northern Research developed for field use. An article in ITWeb, a South African technology publication, says Fujikura's FR-1 of 1978 was the first splice machine, with the technician lining up the fibers by hand under a microscope and each splice taking up to about 30 minutes. Sumitomo Electric says it launched its first fusion splicer in 1980 and, in 1984, one that showed the fiber cores directly through a microscope; a later model added a camera so the machine could align the cores itself.
Credit
Bell-Northern Research and Northern Telecom; Fujikura; Sumitomo Electric
2005
One number before digging
On 10 March 2005 the FCC made 811 the national number to call before digging in the US, as the Pipeline Safety Improvement Act of 2002 required. The call reaches a state One Call center, which tells the owners of buried lines to come and mark them. In 2024, the Common Ground Alliance's DIRT report found telecommunications lines were the most often damaged buried lines, at 49% of reported damages, and that telecom and cable TV work was involved in 23% of damages.
Lessonthe alliance found damages up slightly in 2024 and concluded that voluntary best practices "may be insufficient.".
Credit
FCC; US Congress
2014
Tower deaths draw regulators
OSHA, the US workplace safety agency, counted 13 deaths at communication tower worksites in 2013, the deadliest year since 2006, and 91 deaths from 2003 through 2013, 79 of them from falls. It noted that as many as six or seven layers of subcontractors can sit between a carrier and the workers on the tower. On 14 October 2014 the Labor Department, OSHA and the FCC held a workshop on tower climber safety, and founding documents were signed the same day for a registered apprenticeship program for tower climbers. OSHA counted 12 deaths in 2014, 3 in 2015 and 6 in 2016, published best practices jointly with the FCC in 2017, and in 2018 convened a small-business review panel on a possible tower standard.
LessonOSHA said the layered contracting "poses challenges to setting and enforcing safety rules.".
Credit
OSHA; the FCC; the US Department of Labor
2019
Shallow trenches fail
Google Fiber tried a faster way of laying fiber in Louisville, Kentucky: cutting shallower trenches in the road and sealing the cable in. The sealant did not hold in some areas and cables were exposed. In February 2019 the company said it "would need to essentially rebuild our entire network in Louisville," ended service on 15 April 2019, and agreed to pay the city $3.84 million to remove cable and sealant and repave roads.
Lessona cheaper way to lay fiber saves nothing if it does not survive the road it is in.
Credit
Google Fiber; Louisville Metro Government
Watch for
A robot inside the hub
A fiber distribution hub is a roadside cabinet with 144 to 432 ports serving a neighborhood, and each line must be tested from both ends, which usually takes two technicians, one of them moving the test gear from port to port in the cabinet. Said Yakhyoev, a fiber technician, built Machine2 (M2), a small gantry robot that fits inside a 288-port Clearfield cabinet and plugs a test probe into each port on command, so one technician can test alone. He reports that a vision model trained on 30 positive and 30 negative images spotted dust caps on ports in over 80% of cases.
Achieved whenan operator uses it on routine test jobs and publishes time per hub and error rates, or someone outside measures it.
Claimed by
Said Yakhyoev (LightStep LLC), IEEE ComSoc Technology Blog, January 2026
Drones flown out of sight
The FAA proposed a new rule, Part 108, to allow drone flights beyond the pilot's visual line of sight, including aerial surveying, under permits and certificates. It says such flights, including infrastructure inspection, have so far needed individual waivers or exemptions.
Achieved whena final rule takes effect and a tower owner or carrier reports routine tower or line inspections flown under it.
Claimed by
the FAA and the Transportation Security Administration, August 2025; the comment period was reopened in January 2026
Open
01
A splice made by robot
A bench robot that does the hand steps around a fusion splicer: strip the fiber's coating, clean it, cleave it, load both ends into the splicer, then move the finished splice into the heat-shrink oven. The splicer's own arc and alignment make the join.
The briefCredit · unclaimed02
A lasher that crosses poles
A motorized lasher, the machine that winds wire around a fiber cable to bind it to a steel support wire called a messenger strand, that runs along a waist-high test span and gets itself past a post without a person lifting it.
The briefCredit · unclaimed
Open 01 · the brief
A splice made by robot
The first to publish is credited on this line, and the deliverable moves from Open to Achieved.
What to build
A bench robot that does the hand steps around a fusion splicer: strip the fiber's coating, clean it, cleave it, load both ends into the splicer, then move the finished splice into the heat-shrink oven. The splicer's own arc and alignment make the join.
Why it is still open
A 1998 Ciena patent describes a factory workstation in which a robot arm or gantry carries fibers between splicing steps. In the field, a fiber technician wrote in January 2026 that reaching individual ports in street cabinets "remains a manual process" and that automation now has practical openings in outside-plant work. No published test of a low-cost robot doing the whole splicing sequence was found.
Built with what exists
A current fusion splicer with automatic core alignment, from Fujikura, Sumitomo or another maker; a stripper, cleaver and heat-shrink sleeves; a low-cost SO-101 arm with Hugging Face's LeRobot software (see the Note "No download"); a robot model that learns a task from a few demonstrations, such as NVIDIA GR00T 2 (see the Note "Five demonstrations per task") or Runway Praxis-1 (see the Note "Open robot model weights"); a light source and power meter to measure loss; safety glasses and a fiber-scrap bin. Robot models that learn from a few demonstrations are what bring this within reach of a small team.
First step
Film 20 splices done by hand on the bench, time each step, and record them as LeRobot training episodes.
Done looks like
Fifty filmed attempts on single-mode fiber, with a published tally of completed splices, the splicer's loss estimate and a power-meter reading for each, and the share at or under 0.05 dB.
Open 02 · the brief
A lasher that crosses poles
The first to publish is credited on this line, and the deliverable moves from Open to Achieved.
What to build
A motorized lasher, the machine that winds wire around a fiber cable to bind it to a steel support wire called a messenger strand, that runs along a waist-high test span and gets itself past a post without a person lifting it.
Why it is still open
Installation guidance from the cable maker OCC has the lasher pulled by hand; at each pole the pulling stops, the crew moves the lasher and cable guide past the pole, clamps the lashing wire and forms an expansion loop, then starts again. Meta's Bombyx robot was designed to cross obstacles without help, but on power lines, not telecom strand, and in May 2023 Meta said it would license it to the robotics company Hibot to make it "ready for deployment"; no deployment report was found.
Built with what exists
A standard cable lasher and cable guide; messenger strand and a dummy cable on three short posts; a small motor drive; an SO-101 arm with LeRobot to lift the lasher past each clamp (see the Note "No download"); NVIDIA GR00T 2 to learn the move from demonstrations (see the Note "Five demonstrations per task"); AI agents that write robot programs a person can read (see the Note "Readable robot programs"). No live power lines and no climbing.
First step
Build a three-post test span about one meter off the ground and film a person crossing a post with a hand lasher ten times, to record the steps the robot must copy.
Done looks like
Twenty filmed post crossings with a published tally of those completed without a person touching the lasher, and the spacing of the lashing wire measured on both sides of each post.