BRENNEN

Industries / Transport and vehicles / Shipbuilding and repair

Painting and coating

Painting and coating protect a ship's steel from rust and keep weed and barnacles off the hull, from blasting the steel clean in the yard to the last coat in dry dock.

6

Milestones achieved, from 1761 to 2023.

2

To watch for: announced, not yet confirmed outside.

2

Open deliverables. Nobody has shipped them.

The road

AchievedWatch forOpen

Achieved

  1. 1761

    Copper against shipworm

    The Royal Navy covered the underwater hull of the frigate HMS Alarm with copper plates to keep off shipworm, a wood-boring mollusk. The Naval Marine Archive notes that a 1762 naval manual points to 1761 for the experiment, while the Naval Chronicle gives 1758. The copper ate away the iron bolts that held the hull together by electrolysis; experiments with copper-alloy bolts followed from 1777, the Admiralty ordered all ships below 32 guns coppered in May 1778 and all below 44 guns in July 1778, and a hardened copper bolt was settled on in 1786.

    Lessontwo metals in seawater make a battery, and the coating that saves the hull can destroy what holds it together.

    navalmarinearchive.com

    Credit

    the Royal Navy; bolts by James Keir and Matthew Boulton, later by Westwood and Collins

  2. 1982

    Oysters stop a paint

    Antifouling paints work by leaching a poison into the water so that barnacles and weed cannot settle. At the end of the 1970s Pacific oysters in Arcachon Bay, France, stopped reproducing and grew deformed shells, the first documented harm from tributyltin (TBT), the biocide in some of the most effective paints of the time. France restricted TBT paints step by step from January 1982, and the oyster grounds recovered as concentrations in the water fell.

    Lessonwhat a hull coating releases reaches species it was never aimed at, so it needs testing in the water, not only on the hull.

    doi.org

    Credit

    French researchers, in the account by Claude Alzieu

  3. 2006

    A standard for ballast tanks

    Ballast tanks hold seawater pumped in to keep a ship stable when it is light, and their steel corrodes fast. On 8 December 2006 the International Maritime Organization (IMO) adopted a performance standard for their coatings in new ships of 500 gross tonnage and more: a target life of 15 years, a total dry film thickness of 320 µm (micrometers) for epoxy systems under a "90/10" rule (90% of readings at or above it, none of the rest below 90% of it), at least two stripe coats brushed onto edges and welds plus two spray coats, inspection by certified coating inspectors, and a Coating Technical File recording it all. It became mandatory through SOLAS regulation II-1/3-2.

    wwwcdn.imo.org

    Credit

    IMO Maritime Safety Committee, resolution MSC.215(82)

  4. 2008

    Tin paints banned worldwide

    IMO's International Convention on the Control of Harmful Anti-fouling Systems on Ships, adopted on 5 October 2001, entered into force on 17 September 2008. It forbids ships, including fixed and floating platforms and floating production units, to apply or re-apply antifouling paints that use organotin compounds such as TBT as biocides. IMO says TBT, developed in the 1960s, "has been proven to cause deformations in oysters and sex changes in whelks."

    imo.org

    Credit

    IMO

  5. 2019

    Robots repaint hull sides

    Hapag-Lloyd tested Palfinger's Hull Treatment Carrier on nine of its ships at yards in Hamburg, Marseille and Singapore. The units travel along the hull in dry dock, strip old paint with very high-pressure water and spray new coating at about 600 to 800 m² an hour each, and reach up to 77% of a hull of about 9,300 m². Yard staff still paint the bulbous bow, the area below the bilge keels, the propeller aperture and the flat bottom by hand, and Hapag-Lloyd said paint savings were possible but not confirmed. In February 2025 Damen Shiprepair Dunkerque took delivery of five blast-and-paint robots after trials; it says they paint 100 m² an hour inside an enclosure that stops overspray.

    iims.org.ukdamen.com

    Credit

    Palfinger (maker) and Hapag-Lloyd (tester); Damen Shiprepair Dunkerque

  6. 2023

    The next biocide banned

    In 2021 IMO's Marine Environment Protection Committee added cybutryne, another antifouling biocide, to the convention. Since 1 January 2023 ships may not apply paints containing it, and existing coats must be removed or sealed under a new coating at the next scheduled renewal, no later than 60 months after they were applied.

    Lessonthe convention is built to add substances, so a paint that is legal when a ship is delivered can need replacing within five years.

    imo.org

    Credit

    IMO Marine Environment Protection Committee

Watch for

  1. Robots for Navy ship coatings

    HII, which builds most of the US Navy's large surface ships, has enlisted GrayMatter Robotics to automate blasting, coating and inspection. GrayMatter says its robots are up to 12 times faster than skilled people at the same tasks and cut rework by 95 percent, using AI control software that can be set up for new parts without precise fixtures.

    Achieved whenthe Navy, the US Government Accountability Office or another outside party reports measured coating hours, rework or film thickness for robot-coated work on an HII ship.

    maritime-executive.com

    Claimed by

    GrayMatter Robotics and HII, April 2026

  2. Legged robots for block painting

    Kawasaki Heavy Industries, Shin Kurushima Dockyard and Namura Shipbuilding are developing legged and wheeled robots, steered by what they call "physical AI," to weld, paint and check quality on the outside of hull blocks, including work at height and on curved surfaces. The project runs from March 2026 to March 2027, with ClassNK and the American Bureau of Shipping supporting technical evaluation.

    Achieved whenone of the yards reports the robots painting production blocks, with film thickness and hours measured and checked by ClassNK, ABS or another outside party.

    bairdmaritime.com

    Claimed by

    Kawasaki Heavy Industries and partners, reported October 2026

Open

  1. 01

    Stripe coats by robot

    A robot arm that brushes stripe coats, the extra coats of paint laid along plate edges, weld seams and cutouts before spraying, onto steel test panels built like ballast-tank stiffeners, finding the edges with a depth camera.

    The brief
    Credit · unclaimed
  2. 02

    How much paint lands

    A published, repeatable measurement of transfer efficiency, the share of sprayed paint that ends up on the steel, for hull coatings applied by airless spray, by electrostatic spray and, where one is available, by robot. Weigh the paint drawn from the pot and the panels before and after coating, and check the film thickness.

    The brief
    Credit · unclaimed

Open 01 · the brief

Stripe coats by robot

Credit · unclaimed

The first to publish is credited on this line, and the deliverable moves from Open to Achieved.

What to build

A robot arm that brushes stripe coats, the extra coats of paint laid along plate edges, weld seams and cutouts before spraying, onto steel test panels built like ballast-tank stiffeners, finding the edges with a depth camera.

Why it is still open

IMO's ballast-tank standard requires at least two stripe coats, "applied by brush or roller," with the roller allowed only in scallops and ratholes, so the job is done by painters by hand. A 2021 National Shipbuilding Research Program survey found shipyard coating robots limited to flat surfaces and simple shapes and listed automation of tank coating as a "high investment, high payoff" idea. Hitachi Zosen's Ariake Works reported a robot spraying the inside of ballast tanks in VLCC double-hull blocks in 1999, and Kelm and colleagues (Materials and Corrosion, 2023) tuned a robot that sprays stripe coats onto plates with weld seams for floating wind foundations, reaching 100 to 142 µm. Both spray; neither brushes, which is what the tank standard asks for.

wwwcdn.imo.orgnsrp.orgnippon.zaidan.infodoi.org

Built with what exists

A collaborative six-axis arm such as a Universal Robots UR10e holding a paint brush; a depth camera such as an Intel RealSense to find edges and welds; a waterborne epoxy primer; a magnetic dry film thickness gauge and a low-voltage wet-sponge holiday detector, which finds pinholes. AI agents can draft and test the arm's program in simulation first (see the Note "Readable robot programs").

  1. First step

    Get five welded steel panels with flat-bar stiffeners and cutouts, film a painter stripe coating them, and write a script that finds their edges in a depth-camera scan.

  2. Done looks like

    Ten test panels, each with 20 m of edges, welds and cutouts, stripe coated by the robot and ten by a painter, with dry film thickness readings at set points along every edge, the share meeting the target, holidays found, and minutes per meter, published with photos.

Open 02 · the brief

How much paint lands

Credit · unclaimed

The first to publish is credited on this line, and the deliverable moves from Open to Achieved.

What to build

A published, repeatable measurement of transfer efficiency, the share of sprayed paint that ends up on the steel, for hull coatings applied by airless spray, by electrostatic spray and, where one is available, by robot. Weigh the paint drawn from the pot and the panels before and after coating, and check the film thickness.

Why it is still open

The figures in circulation come from sellers. PPG says electrostatic spraying cut overspray by 40% on the ferry Stena Transporter at EDR Antwerp in June 2024, but its release gives no measurement method, no outside check and no figure for ordinary airless spraying. Damen says conventional painting can waste up to 50% of the paint, and Hapag-Lloyd called paint savings from its hull robots possible but not confirmed.

ppg.comdamen.comiims.org.uk

Built with what exists

The laboratory transfer-efficiency method the US Environmental Protection Agency developed in the 1980s for conventional, electrostatic and airless spray; a lab balance, numbered steel test panels, an airless spray pump, an electrostatic spray gun for liquid coatings, a ventilated spray booth, a dry film thickness gauge and a spreadsheet; waterborne marine primers keep the test safe to run.

osti.gov

  1. First step

    Book time in a university coatings lab or a painters' training center and spray five weighed panels with one waterborne primer by airless spray.

  2. Done looks like

    Transfer efficiency for at least two spray methods on three coatings, five repeats each, published with the full mass balance, booth conditions, film thickness readings and the method, so another lab can repeat it.