BRENNEN

Industries / Industrial equipment and services / Robotics

Arms

Arms are the robot arms themselves: chains of motor-driven joints ending in a wrist that carries a tool or a part, designed, built and sold by robot makers.

7

Milestones achieved, from 1961 to 2024.

1

To watch for: announced, not yet confirmed outside.

2

Open deliverables. Nobody has shipped them.

The road

AchievedWatch forOpen

Achieved

  1. 1961

    The first arm at work

    The first Unimate went to work at General Motors' Ternstedt plant in Trenton, New Jersey, which made door handles and other car hardware. The International Federation of Robotics (IFR), the robot makers' trade body, says its 4,000-pound arm stacked hot die-cast metal parts by following steps stored on a magnetic drum, moved them with hydraulic actuators (pistons driven by oil under pressure), and cost US$65,000 to make but was sold for US$18,000.

    ifr.org

    Credit

    George Devol and Joseph Engelberger (Unimation); General Motors

  2. 1969

    Japan licenses the Unimate

    Unimation licensed Kawasaki Heavy Industries to make and sell Unimate robots for the Asian market. The IFR says that in 1969 Kawasaki developed the Kawasaki-Unimate 2000, "the first industrial robot ever produced in Japan," and became Japan's pioneer in the field.

    ifr.org

    Credit

    Kawasaki Heavy Industries; Unimation

  3. 1973

    Electric motors replace hydraulics

    KUKA, a German maker, says its FAMULUS of 1973 was "the world's first industrial robot with six electric motor-driven axes." ABB says the IRB 6, which its forerunner ASEA supplied in 1974 to Magnusson, an engineering workshop in Genarp, Sweden, was "the world's first all electric industrial robot." The IFR repeats both claims, and adds that the IRB 6 carried 6 kg on five axes and that its controller was the first to use an Intel 8-bit microprocessor.

    kuka.comlibrary.e.abb.comifr.org

    Credit

    KUKA; ASEA (now ABB)

  4. 1978

    An arm built for assembly

    Hiroshi Makino of the University of Yamanashi in Japan developed the SCARA (Selective Compliance Assembly Robot Arm). Its joints turn about parallel upright axes, so the arm gives slightly from side to side but stays stiff up and down, which helps it push a pin into a hole without jamming. The IFR says Sankyo Seiki and Hirata, both Japanese, launched SCARA robots in 1981.

    ifr.org

    Credit

    Hiroshi Makino; Sankyo Seiki; Hirata

  5. 2008

    Arms without a cage

    A collaborative robot, or cobot, is a light arm built to work beside people without a safety fence. Universal Robots, founded in Denmark in 2005 by Esben Østergaard, Kasper Støy and Kristian Kassow, says distributors sold its first UR5 cobots in Denmark and Germany in 2008; the IFR calls the UR5 "the first cost-efficient and user-friendly collaborative robot." Teradyne bought the company for $285 million in 2015, and Universal Robots counted 100,000 cobots sold by 2025. Interact Analysis, a market research firm, counted about 57,000 cobots shipped worldwide by all makers in 2025.

    universal-robots.comifr.orgrobotics247.com

    Credit

    Universal Robots

  6. 2018

    A cheaper cobot maker closes

    Rethink Robotics, founded by Rodney Brooks, launched Baxter, a two-armed cobot, in 2012 at $22,000, low for an industrial robot at the time, and Sawyer, a one-armed model that IEEE Spectrum calls more precise, in 2015. Neither sold well. Brooks liked to show how easy Baxter was to program by grabbing its arms and moving them. The company closed in October 2018 after about $150 million of funding, when sales missed targets in a cobot market that Universal Robots came to dominate and a planned sale of the company fell through. A 2015 University of Illinois thesis measured Baxter's repeatability, how closely it returns to the same point, at 2.9 mm for the left arm and 3.3 mm for the right.

    LessonA low price, a safe design and teaching by hand did not by themselves sell the robot; IEEE Spectrum puts the closure down to sales and competition.

    spectrum.ieee.orgideals.illinois.edu

    Credit

    Rethink Robotics (Rodney Brooks)

  7. 2024

    Chinese makers lead at home

    The IFR says that in 2024, "for the first time, Chinese manufacturers have sold more than foreign suppliers in their home country," with 57% of China's market, up from about 28% a decade earlier; in 2025 their share was 55%, or 195,000 robots. Chinese money had already reached the top tier: Midea, a Chinese appliance maker, bought just under 86% of KUKA in its 2016 takeover offer and took the last shares in a squeeze-out completed on 8 November 2022.

    ifr.orgifr.orgcomputer-automation.dekuka.com

    Credit

    Chinese robot makers; IFR (figures)

Watch for

  1. SoftBank's purchase of ABB Robotics

    SoftBank Group agreed on 8 October 2025 to buy ABB's robotics business, about 7,000 employees, for US$5.375 billion, and expected to close in mid-to-late 2026. On 6 November 2026 SoftBank said that China's Working Mechanism for Foreign Investment Security Review had notified it on 4 November that it prohibited the acquisition of ABB's robotics business in China, and that both companies are "working constructively on the transaction."

    Achieved whenSoftBank announces that the purchase has closed and states which parts of ABB's robot business, including its operations in China, it now owns.

    group.softbankgroup.softbank

    Claimed by

    SoftBank Group, October 2025

Open

  1. 01

    One test for cheap arms

    A side-by-side, published test of repeatability, how closely an arm returns to the same taught point, for the low-cost arms now used to train robot models, run by one method on every arm. The method follows ISO 9283, the international standard for testing industrial robot performance.

    The brief
    Credit · unclaimed
  2. 02

    Take a retired arm apart

    A published teardown of retired small industrial arms, under about 30 kg and without spring counterbalances, bought used, disconnected and never powered, with every part weighed and sorted by material: cast metal, aluminium, copper windings, rare-earth magnets in the motors, gears, electronics and cable. The result is the first measured answer to how many grams of magnet an arm holds per kilogram of payload.

    The brief
    Credit · unclaimed

Open 01 · the brief

One test for cheap arms

Credit · unclaimed

The first to publish is credited on this line, and the deliverable moves from Open to Achieved.

What to build

A side-by-side, published test of repeatability, how closely an arm returns to the same taught point, for the low-cost arms now used to train robot models, run by one method on every arm. The method follows ISO 9283, the international standard for testing industrial robot performance.

Why it is still open

Tests of single robots exist. A 2015 University of Illinois thesis applied ISO 9283 to Rethink's Baxter and measured 2.9 mm and 3.3 mm, and Robonine, a robot-parts site, measured one Feetech STS3215, the servo motor in each joint of the SO-101 arm, at about ±0.3 mm on a 10 cm lever. No comparison of several learning arms under one method turned up.

ideals.illinois.edurobonine.com

Built with what exists

SO-101 arms from Hugging Face's LeRobot project and its software to command them (see the Note "No download"); two or three other arms sold for under US$5,000; dial test indicators reading to 0.01 mm on a rigid printed fixture; a webcam with printed fiducial markers as a second measure; a spreadsheet or Python script for the statistics.

  1. First step

    Build one SO-101, fix a dial indicator at one pose, and record 30 returns at two speeds.

  2. Done looks like

    Five arm models, three units of each, sent to five poses with 30 returns to each pose, at no load and at half the stated payload. Published: each arm's repeatability in millimetres beside its maker's figure, with all raw readings.

Open 02 · the brief

Take a retired arm apart

Credit · unclaimed

The first to publish is credited on this line, and the deliverable moves from Open to Achieved.

What to build

A published teardown of retired small industrial arms, under about 30 kg and without spring counterbalances, bought used, disconnected and never powered, with every part weighed and sorted by material: cast metal, aluminium, copper windings, rare-earth magnets in the motors, gears, electronics and cable. The result is the first measured answer to how many grams of magnet an arm holds per kilogram of payload.

Why it is still open

China's 2025 licensing of rare-earth magnet exports slowed robot motor supply (see "Magnets become a choke point" under Parts and motors), yet no teardown giving the magnet mass of an industrial arm turned up. The figures that circulate are model estimates for humanoid robots, 2 to 4.5 kg of neodymium-iron-boron magnet each, attributed to the Foundation for American Innovation, and the page that reports them says nothing about arms.

humanoid.guidefortune.com

Built with what exists

Used arms and spare servo motors from robot refurbishers and surplus sellers; hand tools and a bearing puller; a 0.1 g scale for magnets and a 10 g scale for castings; magnet-handling gloves and non-magnetic spacers; a phone camera to record each part on the scale.

  1. First step

    Buy one surplus servo motor from a small arm, open it, and weigh its magnets.

  2. Done looks like

    Three arms from three payload classes fully dismantled, with a published table of grams of each material per arm and per motor, photos of every reading, and grams of magnet per kilogram of rated payload.