BRENNEN

Industries / Mining and materials / Packaging

Filling and sealing lines

Filling and sealing lines are the machines that put a measured amount of product into each container, close it, and check that it is full, sealed and safe to open.

6

Milestones achieved, from 1960 to 2008.

2

To watch for: announced, not yet confirmed outside.

2

Open deliverables. Nobody has shipped them.

The road

AchievedWatch forOpen

Achieved

  1. 1960

    Blow, fill and seal

    In 1960 Gerhard Hansen built the first prototype of a bottelpack machine, which blows a plastic container, fills it and seals it in one continuous operation, by the account of Rommelag, the family group he founded; production of the machines began in Germany in 1964. The US FDA's 2004 guidance on aseptic processing, the filling of sterile products under sterile conditions, describes blow-fill-seal as an automated process with "reduced human intervention" that is often used for eye-care and respiratory-care products and, less often, for injectable drugs.

    rommelag.comfda.gov

    Credit

    Gerhard Hansen, by Rommelag's own history

  2. 1970

    Caps children cannot open

    The US Poison Prevention Packaging Act of 30 December 1970 let regulators require "special packaging" for hazardous household substances, including medicines: packaging significantly difficult for children under five to open within a reasonable time, and not difficult for normal adults. Under the test rule, groups of 50 children aged 42 to 51 months try to open the package, and at least 85% must fail without being shown how and 80% after a demonstration. Gregory Rodgers, of the CPSC's Directorate for Economic Analysis, estimated in JAMA in 1996 that child-resistant packaging cut child deaths from oral prescription drugs by about 45% from projected levels, about 460 fewer deaths from 1974 to 1992.

    LessonThe protection is partial; Rodgers credited the packaging with 34% fewer aspirin deaths among young children in a 2002 study and called for further prevention measures.

    law.cornell.edulaw.cornell.edulaw.cornell.eduebi.ac.ukebi.ac.uk

    Credit

    US Congress and the CPSC

  3. 1976

    Filling to the average

    Council Directive 76/211/EEC of 20 January 1976 set common European rules for packs filled to a stated weight or volume. A batch's actual contents must not be less, on average, than the quantity on the label; only a small share of packs may fall short by more than a set tolerance; and no pack short by more than twice that tolerance may carry the small "℮", at least 3 mm high, that is the packer's guarantee that the pack meets the rules. Packers' checks follow sampling plans based on the ISO 2859 standard.

    eur-lex.europa.eu

    Credit

    Council of the European Communities

  4. 1981

    Peroxide cleared for sterile packs

    Aseptic packaging fills a sterilized product into a sterilized package in a sterile space; IFT's Food Technology magazine dates its first use in paper-based cartons to 1961. On 9 January 1981 the US FDA allowed hydrogen peroxide solution of up to 35% to sterilize plastic food-contact surfaces of packaging, so long as no more than 0.5 parts per million of peroxide can be found in water packed under production conditions. The rule asks for sterility at least equal to that of heat-processed metal cans.

    law.cornell.eduift.org

    Credit

    US Food and Drug Administration

  5. 1982

    Seals that show tampering

    Beginning on 29 September 1982, seven people in the Chicago area died after taking Extra-Strength Tylenol capsules laced with cyanide. On 5 November 1982 the FDA required most over-the-counter medicines to be sold in packages whose breach would leave visible evidence of tampering. Johnson & Johnson recalled about 31 million bottles and brought the capsules back in triple-sealed packages, by the University of Illinois Chicago's account. Capsules stayed a target: three people died in 1986, and in February 1991 two people died from cyanide in Sudafed capsules whose package met the FDA standard and showed numerous, conspicuous signs of tampering. In 1998 the FDA required two-piece capsules to be sealed, changed the term "tamper-resistant" to "tamper-evident," and required the label to name every tamper-evident feature on the package.

    LessonA seal protects only people who notice that it is broken, so buyers have to be told which seal to look for.

    federalregister.govlaw.cornell.edupublichealth.uic.edu

    Credit

    US FDA; Johnson & Johnson

  6. 2008

    Machines share one state model

    PackML (Packaging Machine Language), developed by the Organization for Machine Automation and Control (OMAC), gives every machine on a line the same set of states, modes and counts. A filler, a capper and a case packer from different makers can then be started, stopped and measured the same way, including for overall equipment effectiveness (OEE), the share of planned time spent making good product at full speed. The International Society of Automation (ISA) published it as technical report ISA-TR88.00.02 in August 2008. Procter & Gamble, which had found many PackML implementations "not very robust and often too complex", gave OMAC an implementation guide and software in August 2009, as reported by Control Engineering. On 11 November 2020 the OPC Foundation published OPC 30050, which carries PackML over OPC UA, an open protocol for industrial data.

    LessonA shared standard did not on its own make machines behave alike; P&G said uneven implementations often led to software being reworked, so it gave away reference code.

    controleng.comomac.orgreference.opcfoundation.org

    Credit

    OMAC and ISA; Procter & Gamble; OPC Foundation

Watch for

  1. Ten-minute format changes

    Syntegon says format changes on the TRX topload cartoner in its NeXt range can be completed in 10 minutes, with guided, verified or semi-automated steps. It also says autonomous mobile robots bring film reels and carton blanks to the machines, that camera- and AI-based checks detect errors automatically, and that lines can run for hours without a person stepping in.

    Achieved whena customer reports measured changeover times and unattended running hours on a production line, checked by someone outside Syntegon.

    packaginginsights.com

    Claimed by

    Syntegon, at Pack Expo, October 2026

  2. AI that diagnoses filler alarms

    GEA says the operator screen on its new fillers suggests the most likely causes of an alarm and ranked fixes, drawing on data from GEA installations worldwide and learning from how operators resolve alarms. It also says a new gripper allows fully automatic changeovers between bottles with the same neck finish, with no tools, manual adjustments or swapped parts, on fillers that run up to 60,000 bottles an hour.

    Achieved whena bottler publishes before-and-after figures for the time to clear alarms and to change over, or an outside party measures them.

    gea.com

    Claimed by

    GEA, September 2025

Open

  1. 01

    Open packing-line log

    A public record of a real small packaging line, such as a brewery's canning line, logged in PackML states for a full season: every start, stop, fault, changeover and count, with each stop labeled by its cause. Add a baseline that predicts the next stop or splits lost time into OEE losses.

    The brief
    Credit · unclaimed
  2. 02

    Robot swaps capper change parts

    A low-cost robot arm that changes a benchtop capping machine over from one bottle size to another, swapping the chuck that grips the cap and resetting the guides, learned from a few dozen human demonstrations instead of hand-written code.

    The brief
    Credit · unclaimed

Open 01 · the brief

Open packing-line log

Credit · unclaimed

The first to publish is credited on this line, and the deliverable moves from Open to Achieved.

What to build

A public record of a real small packaging line, such as a brewery's canning line, logged in PackML states for a full season: every start, stop, fault, changeover and count, with each stop labeled by its cause. Add a baseline that predicts the next stop or splits lost time into OEE losses.

Why it is still open

PackML defines the states and the OEE data a line should report, but searches of Hugging Face, arXiv and GitHub in November 2026 found no public dataset logged in PackML states. The closest published work describes control code for a laboratory line (Gašper Mušič, 2015).

reference.opcfoundation.orghuggingface.codoi.org

Built with what exists

A Raspberry Pi or small industrial PC; clamp-on current sensors and light barriers, fitted by the line owner's maintenance staff, where machines have no network port; the asyncua Python library or open62541 for OPC UA; and a tablet form on which operators record the cause of each stop.

  1. First step

    Ask a mobile canning company or small brewery to log one week of canning runs by hand on a tablet form keyed to PackML states.

  2. Done looks like

    At least 500 hours of production from one or more lines, with 95% or more of stops labeled by cause, released under an open license together with a baseline and its scores.

Open 02 · the brief

Robot swaps capper change parts

Credit · unclaimed

The first to publish is credited on this line, and the deliverable moves from Open to Achieved.

What to build

A low-cost robot arm that changes a benchtop capping machine over from one bottle size to another, swapping the chuck that grips the cap and resetting the guides, learned from a few dozen human demonstrations instead of hand-written code.

Why it is still open

Line makers automate changeovers with motors and purpose-built robot cells, yet KHS said in May 2023 that some format parts on its can packing systems still have to be replaced by hand. Universal Robots introduced an AI Trainer in March 2026 in which an operator guides one arm while a second copies it, and Packaging World reported in April 2026 that such demonstrations cut reprogramming at changeover, while "mechanical changes still apply where needed". Open robot datasets show low-cost arms putting caps on bottles, such as a LeRobot set of 152 recorded episodes from March 2026, but searches of Hugging Face in November 2026 found none for swapping change parts.

foodtechbiz.compackworld.comhuggingface.co

Built with what exists

A pair of SO-101 arms (a leader arm moved by hand and a follower arm that copies it) with the LeRobot library, an open robot policy such as LeRobot's ACT or NVIDIA's GR00T fine-tuned on the demonstrations, and a benchtop semi-automatic screw capper with interchangeable chucks. NVIDIA reports 95% average success after five demonstrations on its own test tasks (see the Note "Five demonstrations per task").

  1. First step

    With the capper unplugged, record 50 demonstrations of swapping one chuck.

  2. Done looks like

    Twenty filmed changeovers for each of three bottle sizes, published with the success tally, the time per changeover and the same figures for a person doing the job.