BRENNEN

Industries / Industrial equipment and services / Industrial services / MRO supply

Obsolete parts

Obsolete parts work starts when a maker stops making a part a plant still depends on, and covers spotting it early, buying a last supply, finding or approving a substitute, or making a new copy.

5

Milestones achieved, from 1976 to 2007.

2

To watch for: announced, not yet confirmed outside.

3

Open deliverables. Nobody has shipped them.

The road

AchievedWatch forOpen

Achieved

  1. 1976

    A rule for vanishing makers

    On 3 December 1976 the US Department of Defense (DoD) issued Directive 4005.16 on Diminishing Manufacturing Sources and Material Shortages (DMSMS), the loss of the last makers of a part or material. It told DoD components to act in time when production or support was endangered by "the lack, or impending lack, of manufacturing sources for items and material." The Institute for Defense Analyses (IDA) suggests the timing was tied at least partly to problems with electronics, when the department's share of the semiconductor market was only slightly above 10%. A 1983 instruction covered life-of-type buys, a final purchase meant to last the rest of an item's service life.

    ida.org

    Credit

    US Department of Defense

  2. 1991

    Policy dropped, then restored

    In 1991 the DoD replaced its stand-alone DMSMS directive, revised in 1984, with a 562-page acquisition instruction that said little about the problem. IDA notes that this happened at a time of growing concern: a 1989 report had set out an action plan, and the department had lacked a named focal point for DMSMS until a deputy assistant secretary volunteered. Procedures came back in a consolidated materiel management regulation first published in 1993.

    LessonObsolescence work needs its own owner and rules; folded into a general document, it can fade just as the problem grows.

    ida.org

    Credit

    US Department of Defense, as reviewed by IDA in 2017

  3. 1999

    Utilities pool obsolescence work

    Meetings on instrument aging and obsolescence held by INPO, the US nuclear industry's operations institute, in 1995 and 1998 led to no follow-up that Ujal Mondal of the CANDU Owners Group (COG) knew of, and an early shared database of obsolete items held only a handful of components. In November 1999 fifteen US utilities and COG formed the Nuclear Utility Obsolescence Group (NUOG), sponsored by Wolf Creek Nuclear Station, to share obsolete items and their solutions; Mondal reported in November 2000 that it had 30 utilities and 54 stations around the world. Westinghouse, a NUOG member, now runs the Proactive Obsolescence Management System (POMS), which gathers members' equipment and inventory records and contacts each vendor once a year to ask whether each model number is still supported.

    LessonMeetings left nothing behind; a standing group with shared records did.

    proceedings.cns-snc.cawestinghousenuclear.com

    Credit

    Wolf Creek Nuclear Station, fifteen US utilities and the CANDU Owners Group

  4. 2006

    Watching parts before they end

    The DoD's first DMSMS guidebook, SD-22, came out in 2006, and the January 2015 edition was the fifth in ten years; the 2015 edition added guidance for materials and software. IDA describes the change behind it: in the 1970s, when a part became obsolete, staff searched parts catalogs for alternatives, often by hand, while by the late 1980s the aim was to spot coming losses early, which automated tools and databases made possible.

    ida.org

    Credit

    US Department of Defense

  5. 2007

    A world standard for obsolescence

    The International Electrotechnical Commission (IEC) published IEC 62402 on 14 June 2007, a guide to setting up cost-effective obsolescence management through every phase of a product's life. The second edition, which replaced it in 2019, is written as requirements, not a guide: an obsolescence policy, an organization, a management plan, design choices that reduce obsolescence, and measurement of results, for any organization that depends on others for the items it uses.

    webstore.iec.chwebstore.iec.ch

    Credit

    IEC

Watch for

  1. Printing an obsolete boiler part

    Engineers at the US Navy's Naval Surface Warfare Center, Philadelphia Division (NSWCPD), say they are making a 3D-printed replacement for the wallbox of the Boiler Combustion Monitoring System, a protected channel that lets a camera and light look into the furnace of a ship's propulsion boiler; the original part is no longer available through normal supply. The redesign widens a cooling-air gap that the old part restricted and uses Inconel, a heat-resistant nickel alloy, in place of carbon steel. Installation on the six Wasp-class ships and USS Blue Ridge waits on testing and scheduled maintenance periods.

    Achieved whenthe printed wallboxes are installed and an inspection after a period of boiler service is published.

    voxelmatters.com

    Claimed by

    NSWCPD, June 2026

  2. Old drawings into 3D models

    3D Spark says its Voluminate platform, in beta, turns old drawings, DXF files and even photos into 3D models in minutes, which would suit obsolete spare parts. The company itself says the automated geometry is not dimensionally verified, positions it for screening, costing and early evaluation rather than production, and sells engineer-checked models at a higher price.

    Achieved whenan independent test publishes the measured differences between parts made from its automated models and the original drawings or parts.

    all3dp.com

    Claimed by

    3D Spark, September 2026

Open

  1. 01

    Test the replacement finders

    A public test of AI tools that suggest a replacement for a discontinued industrial part, such as a relay, motor starter, sensor, drive or controller module: 200 cases in which the maker named a successor in its own public discontinuation notice, put to each tool and scored on whether it picks the maker's successor or a true equal, and whether it misses a difference in size, mounting, wiring or rating.

    The brief
    Credit · unclaimed
  2. 02

    Rebuild a part from photos

    A measured test of rebuilding small obsolete machine parts, such as plastic knobs, covers, brackets, spacers and gears, from photographs or a scan: AI tools produce the CAD model, the parts are printed, and each copy is measured against the original and fitted back on its machine.

    The brief
    Credit · unclaimed
  3. 03

    Redraw an obsolete control board

    A drop-in replacement for an obsolete low-voltage circuit board from an old machine control, such as an operator keypad and display board or a relay output board: trace the old board's connections from photographs, then have an AI model design a new board from parts still in production that fits the same mounting holes and connectors.

    The brief
    Credit · unclaimed

Open 01 · the brief

Test the replacement finders

Credit · unclaimed

The first to publish is credited on this line, and the deliverable moves from Open to Achieved.

What to build

A public test of AI tools that suggest a replacement for a discontinued industrial part, such as a relay, motor starter, sensor, drive or controller module: 200 cases in which the maker named a successor in its own public discontinuation notice, put to each tool and scored on whether it picks the maker's successor or a true equal, and whether it misses a difference in size, mounting, wiring or rating.

Why it is still open

Commercial tools sell AI cross-references for electronic components (Z2Data, for example), and small open projects such as NexusPart on GitHub (2026) do part substitution with retrieval and a language model but publish no accuracy. Research has tested language models on forecasting obsolescence (Saad and co-authors, 2025), not on choosing replacements. The IAEA warns that an alternative product may not match the original in form, fit or function.

z2data.comgithub.comarxiv.orgwww-pub.iaea.org

Built with what exists

Makers' public discontinuation notices and datasheets; AI models with web search, including one that checks its own work, such as Thinking Machines' Inkling 2 Small (see the Note "Checked without being asked"); a scoring sheet for two engineers.

  1. First step

    Collect 30 discontinuation notices that name a successor from three makers' public support sites and record the official answers.

  2. Done looks like

    200 cases from at least five makers; each tool's first suggestion scored blind by two engineers; the hit rate, the rate of unsafe mismatches (for example a lower voltage or current rating) and every case published.

Open 02 · the brief

Rebuild a part from photos

Credit · unclaimed

The first to publish is credited on this line, and the deliverable moves from Open to Achieved.

What to build

A measured test of rebuilding small obsolete machine parts, such as plastic knobs, covers, brackets, spacers and gears, from photographs or a scan: AI tools produce the CAD model, the parts are printed, and each copy is measured against the original and fitted back on its machine.

Why it is still open

Research models are scored on digital shapes: CADENA (Kabisov and co-authors, 2026) released code, weights and a benchmark of mechanical part meshes. An open scan-to-CAD prototype on GitHub says its output is still faceted, not true CAD, and 3D Spark says Voluminate's automated geometry is not dimensionally verified. No published test was found that measured printed replacements against the parts they replace.

arxiv.orggithub.com

Built with what exists

Phone photogrammetry or a low-cost structured-light scanner; CADENA's open code and weights; 3D Spark's Voluminate beta; FreeCAD; a resin or filament 3D printer; calipers, or a coordinate measuring machine where one is available.

  1. First step

    Gather ten broken or spare plastic parts from old equipment, measure each with calipers, and photograph them for the first tool.

  2. Done looks like

    30 parts that carry no pressure and no safety load, each with 10 key dimensions measured on the original and on the printed copy from each tool and from a person working in CAD; deviations in millimeters, a pass or fail fit test on the machine, and all files published.

Open 03 · the brief

Redraw an obsolete control board

Credit · unclaimed

The first to publish is credited on this line, and the deliverable moves from Open to Achieved.

What to build

A drop-in replacement for an obsolete low-voltage circuit board from an old machine control, such as an operator keypad and display board or a relay output board: trace the old board's connections from photographs, then have an AI model design a new board from parts still in production that fits the same mounting holes and connectors.

Why it is still open

Tracing old boards by hand into the free KiCad design software is an established hobby and trade, as with an Apollo-era test-stand board that Hackaday's writer redrew in KiCad in 2024 from another person's photos, and free tools now trace a board from photographs into a KiCad netlist and schematic in the browser (PCB ReTrace, on GitHub). Anthropic reports that its Claude Fable 5.2 model designed three working devices whose boards needed no electrical changes, but no published attempt was found to have an AI model design a replacement for an obsolete industrial board and test it against the original.

hackaday.comgithub.com

Built with what exists

PCB ReTrace for tracing; KiCad; Claude Fable 5.2 for the new design (see the Note "Three working devices"); a board maker for small runs; a bench power supply and a logic analyzer.

  1. First step

    Buy two surplus units of one obsolete keypad or relay board, photograph both sides of one, and trace it in PCB ReTrace.

  2. Done looks like

    For five different boards, the new board fits the original's mounting and connectors and, on a bench rig at 24 V or less, gives the same outputs as the original for every input in a published test list; design files and results released.