BRENNEN

Industries / Mining and materials / Steel and metals / Machine shops

Milling and turning

This is the cutting itself: a lathe spins the part against a cutting tool to make round shapes, and a milling machine spins a cutter against a part held on a moving table to make flat faces, slots and pockets.

7

Milestones achieved, from c. 1800 to 2011.

1

To watch for: announced, not yet confirmed outside.

2

Open deliverables. Nobody has shipped them.

The road

AchievedWatch forOpen

Achieved

  1. c. 1800

    Lead screws guide the tool

    In 1798 Henry Maudslay left the lock maker Joseph Bramah after a dispute over wages and set up his own business in London, by the Science Museum's account. He saw accurate screw threads as the base of precise engineering, above all the lead screw, a long threaded rod that moves a lathe's cutting tool along the work. Between 1800 and 1805 he made a tool that cut master threads in hardwood or soft metal; these served as temporary lead screws for cutting permanent ones in harder steel. In his screw-cutting lathe, gears from the turning work drove the lead screw, which drew along the saddle carrying the tool. Richard Roberts worked with Maudslay for two years before founding his own machine-tool business in Manchester in 1816.

    collection.sciencemuseumgroup.org.ukcollection.sciencemuseumgroup.org.ukcollection.sciencemuseumgroup.org.ukcollection.sciencemuseumgroup.org.uk

    Credit

    Henry Maudslay

  2. 1861

    One mill, many jobs

    Joseph R. Brown of Brown & Sharpe in Providence, Rhode Island, designed the universal milling machine in 1861 at the suggestion of Frederick W. Howe of the Providence Tool Company. The first job was cutting the spiral grooves of twist drills, which had been filed out of rod by hand, slowly and at high cost. The same machine could cut other spirals and gears. The historian Robert S. Woodbury wrote in 1959 that it embodied "nearly all the basic features of milling machines" of his day, and Scientific American first described it on 27 December 1862.

    archive.org

    Credit

    Joseph R. Brown, Brown & Sharpe; Frederick W. Howe

  3. 1900

    Tools that cut red-hot

    Frederick W. Taylor and Maunsel White of the Bethlehem Steel Company found that heating tool steel to about 1,900 to 2,000 °F (about 1,040 to 1,090 °C), until it "softens or crumbles when touched with a rod", gave tools that kept their edges "even at a red heat clearly visible in daylight". Their patent, filed in October 1899 and granted in February 1901, says such tools cut at one and a half to two and a half times the speed of tools treated at lower heat. The 1911 Encyclopaedia Britannica says the first public demonstration of these "high speed steels" was at the Paris Exhibition of 1900, where White ran Bethlehem's exhibit, according to Grace's Guide.

    patents.google.comen.wikisource.orggracesguide.co.uk

    Credit

    Frederick W. Taylor and Maunsel White, Bethlehem Steel Company

  4. 1926

    Carbide comes to market

    Cemented carbide is grains of very hard tungsten carbide held together by a softer metal. Karl Schröter's patent, filed in the United States in October 1923 and assigned there to General Electric, describes at least 80% tungsten carbide with up to 10% of a lower-melting metal such as iron, cobalt or nickel. Krupp began selling it in Germany in 1926 under the name Widia, from "wie Diamant", like diamond, by the accounts of the toolmaker Mitsubishi Materials and of Kennametal, which owns the brand today. Mitsubishi Materials says General Electric sold its own carbide as Carboloy from 1928, that Toshiba, Sumitomo and Mitsubishi began their own research in Japan around then, and that carbide was much harder than high-speed steel.

    patents.google.commmc-carbide.comaap.com.au

    Credit

    Karl Schröter; Friedrich Krupp AG; General Electric

  5. 1958

    Machines change their own tools

    A machining center is a numerically controlled mill that swaps cutters automatically from a rack or magazine, so one machine can mill, drill, tap and bore a part. In 1958 Hughes Aircraft and Kearney & Trecker of Milwaukee announced a line at Hughes's plant in El Segundo, California, with three machines, for milling, for drilling and tapping, and for boring, all changing tools automatically. It was named the Milwaukee-Matic Model II, and American Machinist says it "ushered in the age of the machining center". The magazine also says a General Electric Mark II control ran a Kearney & Trecker machining center that year, the first machine and control with an effective automatic tool changer. In 2024 machining centers made up 37.7% of the value of Japan's machine tool production, the largest share, ahead of lathes at 26.9%, by METI figures published by JMTBA.

    americanmachinist.comjmtba.or.jp

    Credit

    Kearney & Trecker; Hughes Aircraft; General Electric

  6. 1983

    Turning and milling combined

    A multi-tasking machine, also called a mill-turn, is a lathe with a powered milling spindle and extra axes, so a part can be turned, milled, drilled and bored without being moved to another machine. Yamazaki Mazak of Japan dates its first, the Slant Turn 40N ATC Mill Center, to April 1983. Its Integrex 200Y added a Y axis in 1997, and its Variaxis 200 five-axis machine followed in 1999. Modern Machine Shop reported in 2014 that multi-tasking meant parts could be finished in a single setup, and that at Mazak's own plant in Florence, Kentucky, adding an Integrex e-1060V in 2006 let parts be done in one setup instead of two or three.

    mazak.commmsonline.com

    Credit

    Yamazaki Mazak

  7. 2011

    A lathe kills a student

    On the night of 12 to 13 April 2011, Michele Dufault, a Yale physics and astronomy student, was killed when her hair caught in a rotating part of a lathe in a student machine shop. She was working alone, against the shop's rules. The lathe was 49 years old, had no guards and no emergency stop, and its off button was four to five feet from where she stood. OSHA, the US workplace safety agency, wrote that the lathe lacked an emergency stop, that rules were not posted, and that Yale should make sure students do not work alone; it could not issue citations because she was not an employee. Yale replaced dozens of large power tools, required large emergency stops within easy reach, and made the most hazardous shops open only when a professional supervisor lets students in.

    LessonA trained student still died alone at an unguarded machine; Yale's fix was hardware and access, not more training.

    yalealumnimagazine.comamp.insurancejournal.com

    Credit

    a failure; reported by the Yale Alumni Magazine and, for OSHA's letter, the Associated Press

Watch for

  1. Chatter caught by the machine

    Chatter is a vibration between cutter and part that leaves a rippled surface and wears tools. At the EMO Hannover trade fair in September 2025, DMG MORI showed its fourth-generation NHX horizontal machining centers with CELOS Chatter Control, which, as the Japanese trade site Monoist reported, detects chatter automatically during cutting and writes changed cutting conditions into the NC program with one touch. DMG MORI says the machines' higher spindle power and faster moves cut cycle time by 15%, without a figure for chatter control alone. In April 2026 it also showed camera-based "AI Chip Removal" and monitoring of spindle load and vibration, again without figures.

    Achieved whena user or test lab publishes the chatter cases found and fixed, and tool life and surface finish before and after, over months of production.

    monoist.itmedia.co.jpen.dmgmori.com

    Claimed by

    DMG MORI, September 2025 and April 2026

Open

  1. 01

    Feeds and speeds, cut-tested

    A public comparison of the cutting settings shops are given, from tool makers' calculators, free web calculators, CAM plug-ins and general AI chatbots, against what happens when those settings are cut. For each tool, material and operation, record each source's spindle speed and feed, then cut and measure spindle load, surface roughness, chatter and tool wear after a set length of cut.

    The brief
    Credit · unclaimed
  2. 02

    Chip nest alarm for lathes

    A camera kit that watches a CNC lathe's work area, spots long stringy chips wrapping around the part, chuck or tool, and raises an alarm before they spoil the part or break the tool. Release a public set of labeled videos to train and test it.

    The brief
    Credit · unclaimed

Open 01 · the brief

Feeds and speeds, cut-tested

Credit · unclaimed

The first to publish is credited on this line, and the deliverable moves from Open to Achieved.

What to build

A public comparison of the cutting settings shops are given, from tool makers' calculators, free web calculators, CAM plug-ins and general AI chatbots, against what happens when those settings are cut. For each tool, material and operation, record each source's spindle speed and feed, then cut and measure spindle load, surface roughness, chatter and tool wear after a set length of cut.

Why it is still open

Suggestions are many and measured checks are few. CloudNC launched its Cutting Parameters AI in April 2024 with no test data, only an expected productivity gain of "at least 20%". Uğur Eniş and colleagues (Journal of Advances in Manufacturing Engineering, July 2026) compared language models' answers on face milling with CAM software and digital twin simulations, not with real cuts. Public tool-wear datasets such as Katulu's Uniwear merge laboratory tests on hardened stainless steel and titanium, not common shop materials such as 6061 aluminum or mild steel. A GitHub search for "feeds speeds" in November 2026 found more than a dozen calculators and no published set of measured results to check them against.

cloudnc.comdergipark.org.trgithub.com

Built with what exists

A school or shop CNC mill with a spindle-load readout, run by a trained machinist; carbide end mills from two or three makers; 6061 aluminum and 1018 mild steel; a portable surface roughness tester; a USB microscope to measure flank wear, the worn band behind the cutting edge; a phone microphone to record chatter; a small database to publish the results.

  1. First step

    Pick five common jobs, such as slotting 6061 aluminum with a 10 mm three-flute end mill, collect the suggested settings from every source, and cut the first test block.

  2. Done looks like

    30 combinations of tool, material and operation, each cut at the settings from at least four sources, with measured roughness, spindle load and flank wear after 10 m of cut, published with photos; a ranking of which sources kept tools within their wear limit.

Open 02 · the brief

Chip nest alarm for lathes

Credit · unclaimed

The first to publish is credited on this line, and the deliverable moves from Open to Achieved.

What to build

A camera kit that watches a CNC lathe's work area, spots long stringy chips wrapping around the part, chuck or tool, and raises an alarm before they spoil the part or break the tool. Release a public set of labeled videos to train and test it.

Why it is still open

John McDonald of DMG MORI told Modern Machine Shop in 2022 that of the nest of chips on a lathe chuck, "You can't automate that (away)"; DMG MORI's camera-guided chip flushing needs a new machine and cannot be retrofitted. Ta-Jen Peng and colleagues at National Chin-Yi University of Technology in Taiwan trained a detector for CNC machining chips on synthetic and real images in 2025 and say it can give early warning of chip entanglement, but they report tests on images, not alarms over unattended shifts, and no dataset link was found in the paper. A November 2026 search found no public video set of chip wrapping on lathes.

mmsonline.comsensors.myu-group.co.jp

Built with what exists

An industrial camera in a sealed housing with an air purge, or a Raspberry Pi 5 and camera module behind a window; YOLO object detection models from Ultralytics; Label Studio for labeling; NVIDIA Omniverse for synthetic training images, as in the Peng paper; a stack light or phone message for the alarm, kept separate from the machine's own controls.

  1. First step

    Mount a camera on one lathe running a long job in a material that forms long chips, and record a week of cycles.

  2. Done looks like

    500 labeled clips from at least five lathes in two shops released under an open license; over 100 hours of unattended running at shops that supplied no training clips, the alarm catches at least 90% of the wraps a person marks on the recording, with no more than one false alarm per shift.