Industries / Food, farming and forestry / Forestry and logging / Timber and sawmills / Lumber treating
Drying and fixing after treatment
The work done between the cylinder door and the truck: letting surplus preservative drip off, giving the chemicals time or heat to lock into the wood, and drying out the water that waterborne treatments add.
5
Milestones achieved, from 1990 to 2020.
1
To watch for: announced, not yet confirmed outside.
2
Open deliverables. Nobody has shipped them.
The road
AchievedWatch forOpen
Achieved
1990
Drippage becomes hazardous waste
US Environmental Protection Agency (EPA) rules list wastewater, process residues and "preservative drippage" from wood preserving as hazardous wastes: F032 at plants that use or once used chlorophenol formulations such as pentachlorophenol, F034 at plants using creosote, and F035 at plants using preservatives with arsenic or chromium. Under the same rules, drip pads built after 6 December 1990 count as new. A drip pad must be made of materials other than earth or wood, sloped to drain to a collection system, curbed, and sealed so that liquid passes through it at no more than 1 × 10⁻⁷ cm per second. Treated wood "must be held on the drip pad until drippage has ceased", and the operator must keep records to prove it.
Credit
US EPA
1996
Cleaner wood for water
The Western Wood Preservers Institute (WWPI) published best management practices (BMPs) for treated wood used in water in 1996. Oil preservatives can bleed out of treated wood, sometimes only after the sun heats it, and FPL advises that such pieces should not go into bridges over water. The BMPs set steps at the end of each charge: for creosote, an expansion bath that heats the oil 6 to 12 °C above the pressure-period temperature for at least an hour and then a vacuum, or steaming at no more than 116 °C between two vacuums; for CCA, air seasoning, kiln drying, steaming or a hot-water bath; for ammonia-based copper preservatives (ACZA and ACQ-B), at least 3 weeks of air drying above 16 °C, or kiln drying, so the ammonia leaves. The version revised in November 2011, written with Wood Preservation Canada, the Southern Pressure Treaters' Association and the Southern Forest Products Association, requires a visual check for excessive residue and bleeding before shipment, and says a BMP specification is not complete without inspection by an independent, accredited agency.
Credit
WWPI and its partner associations
1997
Kiln heat counts against wood
Fire-retardant-treated (FRT) plywood and lumber are dried after treatment, to below 15% moisture for plywood and 19% for lumber under the American Wood-Preservers' Association standards C20 and C27, as FPL's Susan LeVan and Mary Collet noted in 1989, when some FRT roof sheathing had turned brittle within 3 to 8 years. Jerrold Winandy of FPL wrote in 1997 that studies showing redrying temperature drove the strength lost in treatment were the basis for a 71 °C (160 °F) limit on redrying FRT material in those standards. In his own tests, plywood redried at 49 °C to 88 °C degraded at much the same rate when later held at 65 °C for up to 290 days, while borate buffers in the treatment slowed the damage. He concluded that heat from redrying and heat in service are "additive and cumulative".
LessonHeat in the kiln after treatment and heat in service add up, so drying after treatment uses part of the wood's working life.
Credit
Jerrold E. Winandy; Susan LeVan and Mary Collet, FPL
2013
Canada holds wood until fixed
In CCA, a waterborne copper, chromium and arsenic preservative, the chromium enters as soluble hexavalent chromium and must be reduced inside the wood before the chemicals stop leaching. Environment Canada's 2013 Technical Recommendations Document for wood preservation facilities requires a fixation process after CCA treatment and says treated wood "shall be held at the treating facility in protected storage until chromium reduction has been completed", shown when hexavalent chromium is not detectable by Method 11 of AWPA standard A3. That method drops chromotropic acid on a fresh boring lying on white blotting paper; any pink to purple color means hexavalent chromium remains, down to 15 parts per million. Fixation takes several hours in a fixation chamber and several weeks near freezing, by the document's account; FPL gives a few hours at 66 °C against weeks or months below 16 °C. The document also gives 48 hours as the usual minimum dripping period.
Credit
Environment and Climate Change Canada; AWPA for the test
2020
Europe's five-minute drip test
The European Commission's Implementing Decision (EU) 2020/2009 of 22 June 2020 set best available techniques (BAT) for plants that preserve wood with chemicals at more than 75 m³ a day, other than those treating only against sapstain. A final vacuum is applied before the treatment vessel opens, unless the starting vacuum was below 50 mbar. Freshly treated wood stays in a contained area until it is dry; before it leaves the drying area, packs are lifted and hung for at least 5 minutes, and if no solution drips the wood "is deemed to be dry". Treated wood is stored on impermeable floors or under cover where the preservative's authorization requires it.
Credit
European Commission
Watch for
Straight joists, dried after treatment
ProWood says its TrueFrame Joist, #1 grade southern yellow pine treated for ground contact (AWPA use category UC4A), is "infused with proprietary next-generation stabilizer additive" and kiln-dried after treatment (KDAT), giving "consistently straight, stable performance", and is planed to within 1/16 inch (1.6 mm). The release gives no measurements of moisture content or warp.
Achieved whensomeone outside the company measures moisture content and bow, crook and twist on these joists and on ordinary treated joists stored and built the same way over at least one season, and publishes the numbers.
Claimed by
ProWood, May 2026
Open
01
A fixation check for copper
A quick test, usable in a treating yard or at a store, that shows whether the copper in freshly treated ACQ, copper azole or ACZA lumber has fixed: for example a damp filter paper pressed to a fresh cut for a set time, its blue copper stain read by a phone camera, calibrated against laboratory leaching of the same boards.
The briefCredit · unclaimed02
Treated lumber, tracked after sale
An open record of moisture content and warp (bow, crook, cup and twist) for pressure-treated lumber bought at retail, wet-treated boards beside KDAT boards, measured on the day of purchase and monthly for a year as they dry outdoors and under cover.
The briefCredit · unclaimed
Open 01 · the brief
A fixation check for copper
The first to publish is credited on this line, and the deliverable moves from Open to Achieved.
What to build
A quick test, usable in a treating yard or at a store, that shows whether the copper in freshly treated ACQ, copper azole or ACZA lumber has fixed: for example a damp filter paper pressed to a fresh cut for a set time, its blue copper stain read by a phone camera, calibrated against laboratory leaching of the same boards.
Why it is still open
FPL's Wood Handbook (2010) says "There is no commonly used method to determine the degree of stabilization" in wood treated with ACZA or ACQ-B; the working rule is that a strong ammonia smell means fixation is not complete. CCA has a blotter test for hexavalent chromium (AWPA A3 Method 11), but nothing comparable was found for copper. Laboratory methods exist: John Ruddick, Wei Xue and Pierre Kennepohl of the University of British Columbia measured how much copper in micronized-copper-treated wood was mobilized and bound using electron paramagnetic resonance and X-ray fluorescence, which need laboratory instruments. A search in November 2026 found no field test.
Built with what exists
Filter paper; chrome azurol S, the copper indicator in AWPA A3; a phone camera and color card; Python with OpenCV; for calibration, a university laboratory running a standard leaching test with copper analysis by X-ray fluorescence; freshly treated boards bought on delivery day and handled with gloves.
First step
Buy freshly treated copper azole boards on a store's delivery day, press filter papers to fresh cuts every day for two weeks, and photograph whether the stain weakens as the wood dries.
Done looks like
On at least 100 boards sampled at several ages after treatment, the quick test sorts boards that leach more copper than a set threshold in the laboratory test from those that do not, at least 85% of the time, with the method, photographs and laboratory results released openly.
Open 02 · the brief
Treated lumber, tracked after sale
The first to publish is credited on this line, and the deliverable moves from Open to Achieved.
What to build
An open record of moisture content and warp (bow, crook, cup and twist) for pressure-treated lumber bought at retail, wet-treated boards beside KDAT boards, measured on the day of purchase and monthly for a year as they dry outdoors and under cover.
Why it is still open
Waterborne treatment raises wood's moisture above the fiber saturation point, about 30%, so it shrinks as it dries in service; Todd Shupe of Louisiana State University with Stan Lebow of FPL and Dennis Ring advise KDAT lumber where dimensional stability matters (2008). Makers sell KDAT products on claims of straightness without published data (ProWood, May 2026). A search in November 2026 found manufacturer notes and forum posts but no controlled study of retail stock.
Built with what exists
A pin-type moisture meter checked against oven-dry samples; a straightedge, a taut string line and feeler gauges, or phone photographs against a grid backdrop, for warp; a covered rack and an open rack; Python or a spreadsheet.
First step
Buy 20 wet-treated and 20 KDAT boards of the same size and length from one store, number them, and record moisture and warp on day one.
Done looks like
At least 200 boards from at least three stores and two treaters, each measured monthly for 12 months and released openly, with the median and spread of moisture loss, shrinkage and each kind of warp for wet-treated and KDAT boards.