Industries / Industrial equipment and services / Industrial services / Industrial cleaning
Vacuum trucks
Vacuum trucks pull liquids, sludge and dry solids up a hose into a sealed tank, using a vacuum pump for liquids or a high-airflow blower for solids, and carry them away for treatment or disposal.
4
Milestones achieved, from 1969 to 2012.
0
To watch for: announced, not yet confirmed outside.
2
Open deliverables. Nobody has shipped them.
The road
AchievedWatch forOpen
Achieved
1969
Jetting and vacuum combined
Vactor, a company founded in Chicago in 1911 as the Myers-Sherman Company to make pneumatic farm equipment, had begun designing sewer and catch-basin cleaners for cities in the early 1960s. In 1969 it launched a sewer cleaner that combined water jetting and vacuuming on one truck.
Credit
Vactor Manufacturing
1978
Vacuum loaders for industry
Vactor dates its Guzzler industrial vacuum loader to 1978. An industrial vacuum loader uses a positive-displacement blower, which on today's Guzzler Classic moves up to about 5,250 cubic feet of air a minute, to pull solids, dry powders, liquids, slurries and thick sludge into a sealed body that it then dumps.
Credit
Vactor and Guzzler, now brands of Federal Signal
2003
Vapor fire at a pit
On 13 January 2003 two vacuum trucks were emptying basic sediment and water (BS&W), the sludge and water drawn off the bottom of gas condensate storage tanks, into an open pit at BLSR Operating's oilfield waste site near Rosharon, Texas. Hydrocarbon vapor from the load ignited, most likely on one truck's own diesel engine, and three people died and four were seriously burned. The US Chemical Safety Board (CSB) found that the shipper, the haulier and the site had not recognized that the mixture was flammable, that the trucks were not grounded, and that the companies were apparently unaware of API RP 2219, the American Petroleum Institute's guidance on vacuum trucks. The CSB asked API to add the danger of unloading flammable liquids onto open ground, and later closed that request as acceptably done; API's current fourth edition, dated June 2016 and reaffirmed in 2024, covers mixtures such as produced water, BS&W and tank bottoms.
LessonA truck's own hot engine can light the vapor it unloads, so flammable loads belong in closed piping, not open pits.
Credit
investigated by the CSB, report approved in September 2003
2012
A vapor limit per load
The Bay Area Air Quality Management District, which regulates air pollution around San Francisco Bay, adopted Rule 8-53 on 18 April 2012 for vacuum trucks at refineries, bulk plants, bulk and marine terminals and organic liquid pipeline facilities. From 1 April 2013 the exhaust of each loading must stay below 500 parts per million of organic vapor, measured as methane, above background, or pass through a control device that removes at least 95%; and each loading must be recorded with its material, volume and exhaust readings.
LessonIn its inventory method, last updated in November 2023, the district still calls its vacuum truck emission estimates highly uncertain, because test results vary widely and most sites do not track the volumes they load.
Credit
Bay Area Air Quality Management District
Open
01
Emissions per load, from records
A public table of how much organic vapor vacuum trucks release per load and per barrel, by material (crude oil, oily water, tank sludge, gasoline), built from an air district's source tests and the loading records its rule requires, obtained under public-records law.
The briefCredit · unclaimed02
Where exhaust vapor drifts
A computer simulation of how vapor from a vacuum truck's exhaust, and from an open unloading point, spreads around the truck in light wind, including the air drawn through the engine's radiator fan, ending in a table of where to point the exhaust hose and how far to keep vapor from the engine's air intake and hot parts.
The briefCredit · unclaimed
Open 01 · the brief
Emissions per load, from records
The first to publish is credited on this line, and the deliverable moves from Open to Achieved.
What to build
A public table of how much organic vapor vacuum trucks release per load and per barrel, by material (crude oil, oily water, tank sludge, gasoline), built from an air district's source tests and the loading records its rule requires, obtained under public-records law.
Why it is still open
The Bay Area district's own inventory method, last updated in November 2023, says vacuum truck estimates "involve significant uncertainty" because of "the wide variation in test results", and that because most facilities do not track vacuum truck volumes closely, data from one refinery was scaled to the others. Its Rule 8-53 has required a record of every loading's material, volume and exhaust readings since April 2013. The Texas Commission on Environmental Quality, in guidance revised in February 2021, estimates vacuum truck emissions with its general formula for loading tank trucks, doubled when an air mover is used, rather than from measurements. No published table of emissions by material was found.
Built with what exists
Requests under the California Public Records Act; a model built for reading long scanned reports, such as Muse Ember (see the Note "The jobs agents repeat"); Python and a spreadsheet.
First step
File a public records request with the Bay Area Air Quality Management District for its vacuum truck source test reports since 2013.
Done looks like
At least 30 source tests and one year of loading records from at least two facilities put into a table; emissions per load and per barrel by material, with ranges, set beside the district's single factor; a second person checks 10 of the reports against the table.
Open 02 · the brief
Where exhaust vapor drifts
The first to publish is credited on this line, and the deliverable moves from Open to Achieved.
What to build
A computer simulation of how vapor from a vacuum truck's exhaust, and from an open unloading point, spreads around the truck in light wind, including the air drawn through the engine's radiator fan, ending in a table of where to point the exhaust hose and how far to keep vapor from the engine's air intake and hot parts.
Why it is still open
At BLSR in 2003 the CSB judged a truck's own diesel engine the most likely ignition source and found that vapor could have been drawn to the hot turbocharger by the radiator fan's airflow. A search for dispersion studies around vacuum trucks found none; the nearest is a 2024 Chalmers University study of liquefied petroleum gas spreading from a leaking road tanker, which used the commercial code FLACS-CFD.
Built with what exists
OpenFOAM, a free computational fluid dynamics code, or NIST's Fire Dynamics Simulator, which also models gas spreading; truck dimensions from a maker's brochure; a coding agent that writes and checks the simulation setups, such as one built on Inkling 2 Small (see the Note "Checked without being asked").
First step
Build a simple truck and wind domain in OpenFOAM and rerun one case from the Chalmers paper.
Done looks like
The setup first rebuilds the Chalmers road-tanker case and reports how far its flammable cloud differs from the published one; then runs three wind speeds, four wind directions and four exhaust-hose positions, and publishes for each the vapor concentration at the engine air intake as a share of the lower flammable limit, with all input files.