BRENNEN

Industries / Media, arts and recreation / Fitness and gyms

Equipment

Equipment is the weights and machines a gym buys, connects and keeps running: free weights, strength machines, and cardio machines such as treadmills and bikes.

7

Milestones achieved, from 1910 to 2017.

1

To watch for: announced, not yet confirmed outside.

2

Open deliverables. Nobody has shipped them.

The road

AchievedWatch forOpen

Achieved

  1. 1910

    Plates on the bar

    Bill Pearl, a five-time Mr. Universe who owned health clubs, told American Spa magazine in 1999 that before 1910 a barbell's load was changed by filling hollow ends with sand, shot or water, which took so long that few people took up lifting. He credits Alan Calvert's Milo barbell set of 1910, which took 5, 10 and 15 lb plates like modern free weights, with letting people change weights quickly.

    americanspa.com

    Credit

    Alan Calvert, Milo Barbell, by Bill Pearl's account

  2. 1952

    A treadmill for the heart

    Dr. Robert Bruce and Wayne Quinton at the University of Washington built the forerunner of today's exercise treadmill in 1952, to diagnose heart and lung disease rather than for workouts, according to the Health & Fitness Association's history of gym equipment.

    healthandfitness.org

    Credit

    Robert Bruce and Wayne Quinton

  3. 1950s

    One frame, many stations

    Harold Zinkin built the first Universal machine, a four-station frame with weight stacks, near the end of the 1950s, by Bill Pearl's account. The Fresno Athletic Hall of Fame says up to eight people could use one at once and that Zinkin sold his Universal Gym Machine Company in 1968.

    americanspa.comfresnoahof.org

    Credit

    Harold Zinkin

  4. 1968

    An electronic exercise bike

    The inventor Keene P. Dimick built the Lifecycle, which the Health & Fitness Association calls the first electronic exercise bike. Augie Nieto incorporated Lifecycle, Inc. in 1977, and the company later became Life Fitness.

    healthandfitness.org

    Credit

    Keene P. Dimick; Augie Nieto

  5. 1970

    Cams and single stations

    Arthur Jones introduced the Nautilus "Blue Monster", a cable machine with cams shaped like a nautilus shell that change the resistance through each movement. Through the 1970s Nautilus made single-station machines with selectable weight stacks the convenient way to train strength, in the Health & Fitness Association's account. Bill Pearl recalled that Jones's first machine was a multi-station unit like Universal's, and that he advised Jones to break it into separate units spread around the gym.

    healthandfitness.orgamericanspa.com

    Credit

    Arthur Jones, Nautilus

  6. 2011

    Members as power plants

    Firms such as ReRev of Clearwater, Florida, and Green Revolution of Ridgefield, Connecticut, were fitting ellipticals and bikes in gyms and colleges to feed electricity into the building. In IEEE Spectrum, Tom Gibson worked out that a person makes only 50 to 150 watts in an hour of hard exercise. At 100 watts for 5 hours a day, a machine makes about 183 kilowatt-hours a year, worth about $18, against several hundred to $1,000 to equip it, so payback would take decades.

    Lessona person is a small generator, and the article notes that the Green Microgym in Portland got most of its energy savings from its solar panels, not from its members.

    spectrum.ieee.org

    Credit

    Tom Gibson, IEEE Spectrum (analysis); ReRev and Green Revolution (retrofits)

  7. 2017

    One language for machines

    The Bluetooth Special Interest Group, the standards body behind Bluetooth, adopted the Fitness Machine Service (FTMS) in February 2017. It gives treadmills, cross trainers (ellipticals), step climbers, stair climbers, rowers and indoor bikes one shared way to send speed, power, heart rate and other readings to an app. It also defines a control point through which an app can set targets or, on a bike, simulate the slope of a road. Makers now list it as built in: Spirit Fitness, for one, says its FTMS machines pair with its app, which passes workouts on to Zwift and Kinomap.

    bluetooth.orgspiritfitness.com

    Credit

    Bluetooth SIG Sports and Fitness Working Group

Watch for

  1. AI plans for whole gyms

    EGYM, a Munich maker of motorized strength machines, says its Genius software writes a training plan for each member from their goals and fitness level, using every machine in the club, and that the plans adapt with every workout. It says the plans draw on over seven billion data points. EoS Fitness began rolling it out in October 2025 in Plano, Texas, and Port St. Lucie, Florida. In April 2026 Fitness First said it would bring Genius to all 220 of its clubs in Germany by summer 2026, after a pilot that began in mid-2025 and that it calls successful, and that the software takes over trainers' paperwork. Neither announcement gives measured results for members.

    Achieved whenan independent trial shows members on Genius plans gain strength, or keep training, at least as well as members on plans written by trainers.

    eosfitness.comhealthclubmanagement.co.uk

    Claimed by

    EGYM, EoS Fitness and Fitness First, October 2025 and April 2026

Open

  1. 01

    Auditing gym weights

    A public survey of what gym weights really weigh. Weigh plates and dumbbells against their labels, and measure the force at the handle of selectorized machines (those with a weight stack and pin) and plate-loaded machines, then publish a table of measured load against labeled load for each make and model.

    The brief
    Credit · unclaimed
  2. 02

    Logging use on racks

    A low-cost clip-on sensor for the equipment that reports nothing about its own use: squat racks, benches and plate-loaded machines. It logs minutes in use and sets per hour, and an open dashboard shows which stations sit idle, which have queues and how much wear each has had, for floor planning and servicing. The hardware files, code and an accuracy test are published.

    The brief
    Credit · unclaimed

Open 01 · the brief

Auditing gym weights

Credit · unclaimed

The first to publish is credited on this line, and the deliverable moves from Open to Achieved.

What to build

A public survey of what gym weights really weigh. Weigh plates and dumbbells against their labels, and measure the force at the handle of selectorized machines (those with a weight stack and pin) and plate-loaded machines, then publish a table of measured load against labeled load for each make and model.

Why it is still open

The best plate checks found are informal forum weighings, summarized by Two Rep Cave in 2018, which found most plates within 5% of the marked weight and one 45 lb plate at 47.2 lb. Breaking Muscle explains that pulleys and levers give machines ratios of 2:1 to 5:1 but cites no measurements. A search of the Crossref research index found no systematic survey.

tworepcave.combreakingmuscle.com

Built with what exists

A calibrated bench scale with 1 g resolution; an S-type load cell with an HX711 amplifier board, or a digital crane scale, for static pulls at a machine's starting position; a phone to photograph labels and serial plates; a shared spreadsheet.

  1. First step

    Borrow a calibrated scale, weigh every plate and dumbbell in one gym with the owner's permission, and publish the sheet.

  2. Done looks like

    1,000 plates and dumbbells and 100 machine models measured in at least 10 gyms, each item weighed twice with the two readings within 0.5%, and the data, method and scale certificate published.

Open 02 · the brief

Logging use on racks

Credit · unclaimed

The first to publish is credited on this line, and the deliverable moves from Open to Achieved.

What to build

A low-cost clip-on sensor for the equipment that reports nothing about its own use: squat racks, benches and plate-loaded machines. It logs minutes in use and sets per hour, and an open dashboard shows which stations sit idle, which have queues and how much wear each has had, for floor planning and servicing. The hardware files, code and an accuracy test are published.

Why it is still open

W8-Scope, a research system from Singapore Management University, used a magnet and motion sensor on weight stacks to identify the weight lifted with 97.5% accuracy in two gyms, but it was a study, not a tool gyms can install. Retrofit sensors for weight-stack machines are now sold: Virtuagym launched Virtuagym Connect in October 2025, which tracks repetitions, sets and weight on existing stack machines and publishes no accuracy figures, and Metric Mate has offered a sensor that replaces the stack pin since 2022. Neither is described for racks or plate-loaded machines, and neither publishes its hardware or an accuracy test. A GitHub search found only a student Arduino prototype with no field data.

api.openalex.orgbusiness.virtuagym.comhypepotamus.com

Built with what exists

ESP32 boards with a Bosch BMI270 motion sensor and a Hall-effect magnet sensor, coin-cell batteries, a Bluetooth Low Energy gateway, and the open-source InfluxDB database with Grafana dashboards.

  1. First step

    Fix one board to one squat rack, log a week of use, and compare it with a staff member's tally for two busy hours.

  2. Done looks like

    30 racks, benches and plate-loaded machines in one gym logged for 30 days, with sensor-counted sets matching hand counts by staff on at least 95% of 500 sampled sets, battery life of at least three months, and hardware files, code and data published.