Industries / Industrial equipment and services / Industrial services / Calibration services
Length and dimension
Length and dimension calibration checks the tools that measure size and shape, from gauge blocks, micrometers and calipers to coordinate measuring machines and laser trackers, against standards traced to the definition of the meter.
7
Milestones achieved, from 1896 to 2021.
1
To watch for: announced, not yet confirmed outside.
2
Open deliverables. Nobody has shipped them.
The road
AchievedWatch forOpen
Achieved
1896
Blocks that add up
Carl Edvard Johansson, a Swedish machinist, worked out in 1896 that a small set of steel blocks, lapped so flat and parallel that two of them cling together when slid into contact, could be stacked to make almost any length; four blocks of 1, 2, 4 and 8 mm, for example, give every whole millimeter from 1 to 15. The cling, called wringing, leaves a film about 25 nm thick, which is now counted as part of the block's length. Henry Ford took up the blocks, and by NIST's account they became industry's main transfer standard for length, the reference that carries a lab's length value to the shop floor.
Credit
Carl Edvard Johansson
1917
Gauge blocks made at home
When World War I cut off the only supply of gauge blocks, which came from Europe, the inventor William Hoke came to the US National Bureau of Standards (NBS) with a way to make them. With money from the Army's Ordnance Department, NBS made 50 sets of 81 blocks each, and square blocks with a center hole are still called Hoke blocks.
LessonA reference standard that comes from a single foreign source can run out when it is needed most.
Credit
William Hoke; NBS
1959
Ferranti's measuring machine
A coordinate measuring machine (CMM) measures a part by recording the position of a probe as it touches the part at many points. Hexagon, which now owns the Italian CMM maker DEA, says the first CMM is generally attributed to the British firm Ferranti in 1959 and that the first one sold went in 1960 to Western Electric's plant in Winston-Salem, North Carolina. It dates DEA's first gantry CMM to 1965, Sheffield's first commercially viable computer-controlled CMM to 1970 and the touch-trigger probe, which signals the instant it touches a surface, to 1972.
Credit
Ferranti
1983
Meter defined by light
From 1889 the meter was the length of one platinum-iridium bar, the international prototype, kept by the International Bureau of Weights and Measures (BIPM) near Paris. In 1960 the General Conference on Weights and Measures (CGPM) redefined it by the wavelength of light from krypton-86, measured with an interferometer, an instrument that measures length by counting light waves; in 1983 it redefined the meter as the distance light travels in vacuum in a set fraction of a second. Since then laboratories can realize the meter with stabilized lasers instead of a bar, and NIST calibrates its master gauge blocks by interferometry.
Credit
CGPM and BIPM
1985
Lasers follow robot arms
A laser tracker aims a laser beam at a reflector carried on a moving object and measures its position in three dimensions, so that large structures, machine tools and robots can be measured and calibrated where they stand. In June 1985 K. Lau, R. Hocken and L. Haynes of NBS described two automatic laser tracking techniques that followed a robot's tool end to within a few parts in 100,000 and proposed them as portable calibration tools. An account by the tracker maker API says Kam Lau began the work in the NBS basement in April 1982 and showed a prototype six months later.
Credit
Kam Lau, NBS
1990
Hubble's misplaced lens
The main mirror of the Hubble Space Telescope was polished to the wrong shape because the reflective null corrector, the optical test instrument that guided and checked the polishing, had a lens out of place by 1.3 mm. NASA's board of investigation found that the mirror's maker, Perkin-Elmer, did not re-verify the corrector's dimensions after assembly, and that two other test instruments had shown the error but their results were dismissed as flawed themselves.
LessonA single reference instrument that nobody checks independently can pass a gross error, and when two checks disagree the disagreement must be resolved, not dismissed.
Credit
NASA's Hubble Space Telescope Optical Systems Board of Investigation
2021
Gauge blocks calibrated unattended
Calibrating gauge blocks by mechanical comparison, measuring each against a reference block of the same size on a comparator, needs tightly controlled room conditions and a lot of a technician's time. In 2021 Pablo Constantino and Alejandro Acquarone of LATU, Uruguay's national metrology institute, published a robotized comparator built from simple hardware, whose software runs the whole process, logs the room conditions and readings, and works out each result and its uncertainty with no technician involved. Singapore's National Metrology Centre runs a commercial system of the same kind, an Octagon Precision GBC 170 that loads and unloads blocks by robot and runs a five-point, three-repeat cycle of 8.5 hours without manual intervention.
Credit
LATU (Pablo Constantino, Alejandro Acquarone); Octagon Precision
Watch for
NIST's vision machine rebuilt
NIST calibrates glass scales and other vision artifacts, the patterned plates used to check camera-based measuring machines, on its M48 vision measurement system, a camera fitted to its primary CMM. Its staff wrote that worn hardware had made the system less reliable, "causing long lead times for calibrations", and that after upgrades they propose expanded uncertainties of 0.092 µm plus a length-dependent term for one-dimensional measurements and 0.24 µm plus a length-dependent term for two-dimensional ones, against a typical 0.15 to 0.50 µm now, validated on NIST's own long-term check standards.
Achieved whenthe new uncertainties are borne out in a comparison with another national laboratory or accepted in NIST's published calibration capabilities.
Claimed by
Maxwell Praniewicz, John Stoup and Wei Ren of NIST, October 2026
Open
01
An open gauge block interferometer
A gauge block interferometer built from available parts and published as open hardware and software. It measures steel gauge blocks wrung to a flat platen by reading the fraction of a light fringe at known laser wavelengths, corrects for air temperature, pressure and humidity, and reports each length with a full uncertainty budget.
The briefCredit · unclaimed02
A robot that wrings blocks
A robot that cleans gauge blocks and wrings them together into a stack, and a test of how repeatable its stacks are compared with a skilled person's.
The briefCredit · unclaimed
Open 01 · the brief
An open gauge block interferometer
The first to publish is credited on this line, and the deliverable moves from Open to Achieved.
What to build
A gauge block interferometer built from available parts and published as open hardware and software. It measures steel gauge blocks wrung to a flat platen by reading the fraction of a light fringe at known laser wavelengths, corrects for air temperature, pressure and humidity, and reports each length with a full uncertainty budget.
Why it is still open
Gauge block interferometers are sold to national institutes and accredited labs; NPL's design, made under license by Hexagon, is what NPL calls the de facto commercial instrument, with uncertainties of 20 nm at 1 mm and 40 nm at 100 mm. The open projects found measure changes in distance, not the length of a block. The nmWave interferometer (MIT license, 2024) aims at sub-micrometer displacement over hundreds of millimeters and calls itself a work in progress, and a 2020 Hackaday "$1 laser interferometer" counted fringes from a vibrating speaker without comparing them with any reference. The software half is open: New Zealand's Measurement Standards Laboratory publishes ls-fringeapp, its own code for analyzing gauge block fringe images, updated in December 2025, but not the instrument it runs on.
Built with what exists
A frequency-stabilized helium-neon laser with a certified wavelength; a second, green source such as the long-coherence Osram PLT5 516FA laser diode that nmWave uses; a Twyman-Green layout from optical breadboard parts and a machine-vision camera; platinum resistance thermometers, a barometer and a humidity sensor for the air correction; MSL's open ls-fringeapp, or Python with NumPy and OpenCV, for the fringe analysis; ten grade K gauge blocks, the grade used as calibration masters, with an accredited interferometric certificate as the check. Lasers are kept at eye-safe power with standard laser-safety practice.
First step
Buy two certified blocks and a platen, build a single-wavelength Twyman-Green on a breadboard, and photograph the fringes on a block wrung to the platen.
Done looks like
Ten certified blocks from 1 mm to 100 mm measured, each in at least three separate wrings, with results, uncertainty budget, drawings and code published; at least eight of the ten agreeing with their certificates within the combined uncertainty (a normalized error, the difference divided by the combined expanded uncertainty, of 1 or less); a stated expanded uncertainty under 100 nm at 100 mm.
Open 02 · the brief
A robot that wrings blocks
The first to publish is credited on this line, and the deliverable moves from Open to Achieved.
What to build
A robot that cleans gauge blocks and wrings them together into a stack, and a test of how repeatable its stacks are compared with a skilled person's.
Why it is still open
The automated systems found measure single blocks and leave wringing to people: LATU's and Octagon's robotized comparators move one block at a time, and NPL's commercial interferometer measures up to 12 blocks that have first been wrung to a platen. Hill Cox wrote in Quality Magazine in 2005 that "few laboratories test personnel to see how well they can repeatedly wring up a stack of blocks", and that the variation of a stack re-measured in the same place shows the wringing skill of the person who built it. Searches found no robot that wrings gauge blocks.
Built with what exists
A collaborative arm with force sensing, such as a Universal Robots UR5e, with soft gripper pads; lint-free wipes and an isopropyl alcohol cleaning station; LeRobot to record demonstrations from a skilled metrologist and train (see the Note "No download"); an open robot model such as Runway's Praxis-1 (see the Note "Open robot model weights"); a mechanical gauge block comparator and an optical flat to judge each wring.
First step
Film an experienced metrologist wringing a two-block stack 20 times while the arm records in teach mode, and measure each result on a comparator.
Done looks like
Following Cox's test, a four-block, 25 mm stack wrung 30 times by the robot and 30 times by an experienced person and measured in the same place on a comparator each time; a published spread for each set of 30, the share of robot wrings that fail (blocks that slip or show gaps under the optical flat), and video of every attempt.