BRENNEN

Industries / Industrial equipment and services / Industrial machinery / Bearings

Design and assembly

Design and assembly is the work of choosing how a bearing's rings, rolling elements and cage are laid out, and of putting the finished parts together into a bearing that turns freely.

6

Milestones achieved, from 1898 to 2024.

1

To watch for: announced, not yet confirmed outside.

2

Open deliverables. Nobody has shipped them.

The road

AchievedWatch forOpen

Achieved

  1. 1898

    Rollers shaped as cones

    Henry Timken and Reginald Heinzelman of St. Louis, Missouri, applied in August 1897 for a patent on a roller bearing for vehicle wheels, granted on 28 June 1898 as US 606,635. Its rollers are cones that roll between a cone on the axle and a conical box in the hub, so the load is carried by rolling, not sliding. Ribs on the cone keep the rollers from slipping out endwise or twisting, and the bearing can be adjusted, with the rollers moving in or out evenly. This is the layout of the tapered roller bearing.

    patents.google.com

    Credit

    Henry Timken and Reginald Heinzelman

  2. 1906

    Balls in without a notch

    Robert Conrad applied in February 1904 for a US patent, granted on 5 June 1906 as US 822,723, on a way to fill a ball bearing whose grooves run unbroken all the way round. The inner ring is pushed off center inside the outer ring, which opens a crescent-shaped gap wide enough for a limited number of balls. The rings are then centered again, and spacers slipped between the balls spread them evenly; joined together, the spacers form a cage. The patent sets this against bearings that let the balls in through a recess cut in the side of a ring. Ball bearings filled this way are still called Conrad bearings; Wikipedia's summary says a bearing filled through notches holds more balls but cannot carry much load along the shaft.

    patents.google.comen.wikipedia.org

    Credit

    Robert Conrad

  3. 1907

    A bearing that tilts

    At the Gamlestadens Fabriker textile plant in Sweden, the bearings on long overhead line shafts kept failing, and Machine Design adds that ground softened by rain bent the shafts slightly. Sven Wingquist, who worked there, conceived a self-aligning ball bearing in March 1907: its balls run in a sphere-shaped track in the outer ring, so the bearing keeps turning freely when the shaft is out of line. Svenska Kullagerfabriken (SKF, the Swedish Ball Bearing Factory) was founded the same year to sell it.

    machinedesign.com

    Credit

    Sven Wingquist; SKF

  4. 1950

    A cage for needle rollers

    Needle roller bearings use long, thin rollers. Without a cage, the long rollers tended to skew and jam, and they rubbed against each other as they turned. Georg Schaeffler's answer was a cage that holds each needle parallel to the shaft. Schaeffler says trials began in February 1950, a patent application followed in September 1950, and the first series orders from carmakers came in February 1951. By the company's own count in 2020, it had sold more than 100 billion needle roller bearings since the patent application and was making about 60 billion needle rollers a year.

    schaeffler-tomorrow.deindustrial-production.de

    Credit

    Georg Schaeffler, with his brother Wilhelm Schaeffler

  5. 2017

    Robots run a bearing line

    In June 2017 SKF opened a production unit for spherical roller bearings in Gothenburg that it called fully automated and the first of its type in the group, after announcing a modernization of SEK 190 million in April 2015. Mining Weekly reported in 2018 that it replaced four conventional lines, each making one type of bearing, with one line of 22 industrial robots in four units, for grinding, assembly, marking and lubrication, coordinated by 25 software applications; one robot's grippers adapt in three seconds to rings from 180 to 400 mm across. The paper gave SKF's aim as flexibility across many sizes in small volumes, not more output. The Gothenburg plant makes over a million bearings a year, by SKF's figures.

    manufacturingtomorrow.comminingweekly.comnews.cision.com

    Credit

    SKF

  6. 2024

    Clean bearings get a test

    Dirt left in a bearing during manufacture can damage it later. SKF wrote in 2020 that an extensive study of the manufacturing issues behind its bearings' reliability found cleanliness the single most significant factor, that every part is washed several times on its way to final assembly, and that one flushing station with multiple jets cut particle contamination on freshly ground parts by 80%. ISO 7544:2024 now sets out procedures and equipment for checking how clean rolling bearings and their parts are, for open bearings and for capped ones before grease is put in.

    iso.orgevolution.skf.com

    Credit

    ISO; SKF

Watch for

  1. Humanoids handle bearing rings

    Humanoid, a robot maker, and Schaeffler said in October 2025 that Humanoid's pre-alpha robot had picked metallic bearing rings out of a cluttered bin in a near-production setting at Schaeffler's site in Erlangen, Germany, and that a second phase would follow in production with its alpha robot. In May 2026 Humanoid said Schaeffler would deploy a four-digit number of its wheeled robots across Schaeffler's plants by 2032, starting at two German sites from December 2026 to June 2027. The reports give no pick rates, error rates or uptime.

    Achieved whensomeone outside the two companies reports humanoid robots doing routine production work in a Schaeffler bearing plant, with the number of robots, the tasks and measured rates.

    robotics247.comrobotics247.com

    Claimed by

    Humanoid and Schaeffler, October 2025 and May 2026

Open

  1. 01

    Assemble a bearing by robot

    A low-cost robot arm, trained from human demonstrations, that assembles a small deep-groove ball bearing from loose parts the way Conrad's 1906 patent describes: set the inner ring off center in the outer ring, drop the balls into the gap, center the rings, spread the balls evenly, and press in a snap-in plastic cage.

    The brief
    Credit · unclaimed
  2. 02

    How clean new bearings are

    An independent, published comparison of how much loose dirt new bearings carry out of the box, across makers and sellers, made by washing open (unsealed) bearings of one size, catching the particles on a membrane filter, and counting and sizing them under a microscope.

    The brief
    Credit · unclaimed

Open 01 · the brief

Assemble a bearing by robot

Credit · unclaimed

The first to publish is credited on this line, and the deliverable moves from Open to Achieved.

What to build

A low-cost robot arm, trained from human demonstrations, that assembles a small deep-groove ball bearing from loose parts the way Conrad's 1906 patent describes: set the inner ring off center in the outer ring, drop the balls into the gap, center the rings, spread the balls evenly, and press in a snap-in plastic cage.

Why it is still open

The open robot data sets on Hugging Face that involve bearings stop short of this. BearingALOHA's sets (200 and 70 recorded runs, April 2026) pick up a bearing and place it on a plate, axiboai's set (174 runs, July 2026) inserts a whole bearing, and a third moves loose chrome balls between trays. A 2025 study of deep-groove ball bearing fitting by Peiqi Yang and colleagues says manual fitting is slow and automatic fitting lines have a low success rate and stop when parts do not match. Searches of GitHub, Hugging Face and the web in November 2026 found no robot that learned to assemble a bearing from its parts.

huggingface.cohuggingface.codoaj.org

Built with what exists

An SO-101 arm and the LeRobot software library (the Note "No download" covers LeRobot v0.7.0); a policy fine-tuned from an open robot model such as Runway's Praxis-1 (the Note "Open robot model weights") or NVIDIA's GR00T 2, which by NVIDIA's own test averaged 95% success after five demonstrations on 50 tasks (the Note "Five demonstrations per task"); a wrist camera; a 3D-printed fixture; new bearings with snap-in plastic cages, taken apart to supply the parts.

  1. First step

    Record 50 teleoperated demonstrations of the step that needs most care, spreading the balls evenly once the rings are centered, and train a first policy on that step alone.

  2. Done looks like

    20 filmed attempts from parts laid out at random, with a published tally of bearings completed with every ball in place, the cage fully seated and the bearing spinning freely by hand, and the data, code and trained policy released.

Open 02 · the brief

How clean new bearings are

Credit · unclaimed

The first to publish is credited on this line, and the deliverable moves from Open to Achieved.

What to build

An independent, published comparison of how much loose dirt new bearings carry out of the box, across makers and sellers, made by washing open (unsealed) bearings of one size, catching the particles on a membrane filter, and counting and sizing them under a microscope.

Why it is still open

ISO 7544:2024 sets test methods, but makers keep their results to themselves. SKF describes its own washing and cleanliness targets, and Oxford Instruments' worked example counted 31,249 particles from one wash of finished deep-groove ball bearings from an unnamed production process. A web search in November 2026 found no comparison of particle counts in new bearings between brands or sellers.

iso.orgoxinst.comevolution.skf.com

Built with what exists

A vacuum filtration funnel and membrane filters; a filtered, non-flammable cleaning fluid; an optical microscope with a camera; particle counting in Fiji (ImageJ) or with a segmentation model such as Meta's Segment Anything; blank runs with no bearing to measure the background; ISO 7544:2024 for the method, bought from ISO.

  1. First step

    Wash three new open bearings of one brand alongside three blanks, and check whether the bearings' counts stand clearly above the blanks.

  2. Done looks like

    At least 10 bearings of one size from each of at least five makers or sellers, with particle counts in fixed size classes for every bearing, blanks, and a second wash showing how much the first one recovered; all counts and filter images published.