BRENNEN

Industries / Transport and vehicles / Aerospace and defense

Engines

This is the work of designing, building, inspecting and repairing the gas-turbine engines that push aircraft through the air, from the metal in a single turbine blade to the checks that decide when an engine must come off the wing.

7

Milestones achieved, from 1939 to 2023.

3

To watch for: announced, not yet confirmed outside.

2

Open deliverables. Nobody has shipped them.

The road

AchievedWatch forOpen

Achieved

  1. 1939

    Jet engines run and fly

    A jet engine pulls in air, squeezes it with a spinning compressor, burns fuel in it, and uses the hot gas to drive a turbine that keeps the compressor turning. Frank Whittle's bench engine first ran on 12 April 1937, according to the Smithsonian. Hans von Ohain's HeS 3B engine flew in the Heinkel He 178 on 27 August 1939, which engine maker MTU Aero Engines calls the world's first turbojet aircraft.

    airandspace.si.eduaeroreport.de

    Credit

    Frank Whittle (Power Jets Ltd); Hans von Ohain and Max Hahn at Heinkel

  2. 1970

    High-bypass fans reach airlines

    A turbofan puts a large fan in front of the jet core. Bypass ratio is the share of air the fan pushes around the core rather than through it, and a high ratio saves fuel. The US Centennial of Flight Commission says GE's TF39, chosen for the C-5 cargo plane in 1965, was the first high-bypass turbofan to enter service, and GE says it burned a quarter less fuel than other engines of its day. Pratt & Whitney's JT9D took the Boeing 747 into airline service in 1970, and the Smithsonian calls it the first of the very large high-bypass turbofans in commercial service.

    centennialofflight.netairandspace.si.edugeaerospace.com

    Credit

    GE (TF39, later the CF6); Pratt & Whitney (JT9D)

  3. 1980s

    Blades grown as one crystal

    Ordinary cast turbine blades are made of many metal grains, and the boundaries between grains are weak spots where cracks start. A Pratt & Whitney team cast blades as a single crystal with no grain boundaries, which resist cracking and creep (slow stretching under heat and load). According to ASME, the engineering society, these blades first went into commercial service in the JT9D-7R4 engine in the early 1980s. ASME named the blade a historic engineering landmark in 2018.

    asme.org

    Credit

    Pratt & Whitney's materials laboratory, in a team led by Maurice "Bud" Shank and Frank VerSnyder

  4. 1989

    A hidden flaw in titanium

    On 19 July 1989 the titanium fan disk of a GE CF6-6 engine on United Airlines Flight 232, a DC-10, broke apart, and the plane crash-landed at Sioux City, Iowa; the FAA counts 111 deaths. The crack grew from a flaw formed when the metal was made in 1971, and it was missed in six fluorescent-penetrant inspections, in which a dye seeps into cracks and glows under ultraviolet light. Afterwards spinning disks were designed on the assumption that a flaw may already be inside them.

    LessonParts had been given service lives "assuming no defects", and the FAA's stated lesson is that repeated inspection of critical engine parts has built-in limits.

    faa.gov

    Credit

    NTSB investigation; FAA and engine makers for the follow-up rules

  5. 2015

    Printed parts certified to fly

    Additive manufacturing, or 3D printing, builds a metal part layer by layer by melting powder with a laser or electron beam. In 2015 the FAA certified a printed sensor housing for GE90 engines, which GE calls the first 3D-printed part certified to fly inside GE commercial engines. From 2015 GE's plant in Auburn, Alabama, made printed fuel nozzle tips for the CFM LEAP engine, which entered service in 2016. Each tip is one piece instead of about 20 welded and brazed parts, and the plant shipped its 100,000th tip in 2021.

    ge.commadeinalabama.com

    Credit

    GE Aviation (now GE Aerospace); CFM International, the GE and Safran joint company

  6. 2018

    Borescope checks every 80 cycles

    A borescope is a thin camera on a probe that is pushed through small ports to see blades without taking the engine apart. Cracks were found in compressor blades of Rolls-Royce Trent 1000 engines on Boeing 787s. In April 2018 EASA, Europe's aviation regulator, ordered repeated borescope checks of every affected engine on the wing, with one blade row checked at least every 80 flight cycles.

    LessonFrequent inspection can keep a cracking part flying safely, but EASA called its own rule "an interim action", not a fix.

    ad.easa.europa.eu

    Credit

    EASA (airworthiness directive 2018-0084); Rolls-Royce

  7. 2023

    A flaw in the powder

    Some of the hottest, fastest-spinning engine disks are made by powder metallurgy, pressing and heating fine metal powder into a solid part. In 2023 Pratt & Whitney disclosed a rare condition in that powder for its PW1100G geared turbofan on the Airbus A320neo, and its parent company RTX said about 600 to 700 extra engine removals would follow between 2023 and 2026. In March 2024 the FAA ordered ultrasonic checks and early replacement of parts from certain powder production campaigns and estimated that 430 engines on US-registered airplanes were affected.

    LessonA flaw in one batch of raw material reaches every part made from that batch, so batch records decided how many engines had to come off the wing.

    prnewswire.comgovinfo.gov

    Credit

    disclosure by RTX and Pratt & Whitney; FAA directive 2024-05-11

Watch for

  1. AI reads borescope video

    Pratt & Whitney bought Aiir Innovations, an Amsterdam company whose software applies AI to borescope video. It says the software has been used on V2500 engines and piloted on its geared turbofan, and that AI-enabled borescope inspection has cut overall inspection time by more than 30%, with report writing going "from hours to minutes".

    Achieved whenan airline, repair shop or regulator publishes measured inspection times and missed-defect rates for the tool, compared with human-only inspection of the same engines.

    rtx.comrtx.com

    Claimed by

    Pratt & Whitney and RTX, July and September 2026

  2. Open fan nears full-scale tests

    CFM's RISE program studies an open fan, an engine design without the usual casing around the fan. CFM says the program has run about 500 test campaigns, is preparing to test a full-size front section in a new 8-metre test cell at Villaroche, France, and is aiming for more than 20% better fuel burn than engines in service today.

    Achieved whena complete open fan engine flies and a regulator or airline service data confirm its fuel burn against today's engines.

    geaerospace.com

    Claimed by

    CFM International (GE Aerospace and Safran), July 2026

  3. Doubling time on wing

    Time on wing is how long an engine flies between shop visits. The FAA and EASA certified CFM's high-pressure turbine durability kit for the LEAP-1B engine, and CFM said the kit "will double time on wing in hot and harsh environments like in Middle East and India." Certification confirms the kit is safe to fly; it does not confirm the durability gain.

    Achieved whenairlines in those regions, or an independent fleet-data firm, publish shop-visit intervals showing that kitted engines stay on wing about twice as long.

    geaerospace.com

    Claimed by

    CFM International, July 2026

Open

  1. 01

    Measured damage on scrap blades

    A public set of photos of retired civil-engine compressor and turbine blades taken through an ordinary articulating borescope, with every nick, dent, crack and burn also measured on the real part in millimetres, and a baseline AI model that finds each defect and estimates its size. The set is for research and teaching, never for deciding whether a part may fly.

    The brief
    Credit · unclaimed
  2. 02

    Engine directives sorted by cause

    A public table of every US airworthiness directive (a binding inspection or repair order from the regulator) on aircraft engines, with columns for engine model, part, cause from a fixed list (fatigue crack, material or manufacturing flaw, wear, corrosion, foreign object), inspection method ordered (borescope, ultrasonic, eddy current, fluorescent penetrant) and repeat interval, each row linked to the rule text.

    The brief
    Credit · unclaimed

Open 01 · the brief

Measured damage on scrap blades

Credit · unclaimed

The first to publish is credited on this line, and the deliverable moves from Open to Achieved.

What to build

A public set of photos of retired civil-engine compressor and turbine blades taken through an ordinary articulating borescope, with every nick, dent, crack and burn also measured on the real part in millimetres, and a baseline AI model that finds each defect and estimates its size. The set is for research and teaching, never for deciding whether a part may fly.

Why it is still open

A July 2026 study from Hamburg University of Technology says visual defect inspection "remains predominantly manual" and that annotated defect images are often unavailable. When 50 industry inspectors judged blade images in a 2021 study, their accuracy on borescope views was 63.8%. Public sets such as AeBAD label pixels, not physical size, and a search found no public set that pairs real borescope images with defect sizes measured on the part.

doi.orgdoi.orgarxiv.org

Built with what exists

Civil scrap blades sold as display pieces; a USB articulating borescope; a printed millimetre scale; digital calipers, a dial depth gauge and a USB microscope; Label Studio for labelling; Meta's Segment Anything (SAM 2) to speed up outlines; Ultralytics YOLO as the baseline detector; Hugging Face to host the set. Optionally, a low-cost arm driven through Hugging Face LeRobot holds the probe at the same angles every time (the Note "No download" covers LeRobot).

  1. First step

    Buy ten civil scrap blades, avoiding military-origin parts, which can carry export rules. Photograph each at three fixed angles next to a millimetre scale, measure every visible defect, and post the first 30 labelled images with the measuring method.

  2. Done looks like

    At least 100 blades and 1,000 images under an open licence, each defect with its measured length (and depth, for dents) in millimetres, and a published table of the baseline model's detection rate by defect type and its median size error in millimetres on blades held out from training.

Open 02 · the brief

Engine directives sorted by cause

Credit · unclaimed

The first to publish is credited on this line, and the deliverable moves from Open to Achieved.

What to build

A public table of every US airworthiness directive (a binding inspection or repair order from the regulator) on aircraft engines, with columns for engine model, part, cause from a fixed list (fatigue crack, material or manufacturing flaw, wear, corrosion, foreign object), inspection method ordered (borescope, ultrasonic, eddy current, fluorescent penetrant) and repeat interval, each row linked to the rule text.

Why it is still open

Directives are long, semi-structured documents read by hand. A 2026 TU Wien thesis says manual analysis has "become insufficient" and built an AI pipeline, but only to work out which aircraft a directive applies to, not its cause. A public set of about 22,900 FAA rules tags maker and model and sorts by component only where the text allows. A search found no public table of engine directives sorted by cause.

repositum.tuwien.atai-analytics.org

Built with what exists

The Federal Register's public API; Python; an AI model such as Claude filling a fixed form for each directive; a spreadsheet for human checks. The TU Wien thesis reports 93.84% accuracy for this kind of form-guided extraction. The Note "Seven more flagged" covers a Claude-based reviewer of long regulated documents.

  1. First step

    Pull the 2024 FAA final rules with "Engines" in the title from the Federal Register API, set aside the piston-engine ones, write the cause list, and have two people code the rest to test it.

  2. Done looks like

    All FAA final-rule directives on engines from 2000 to 2025 in one open table, with 200 random rows coded separately by two people and the agreement between model and people on cause and inspection method published, reaching at least 90%.