BRENNEN

Industries / Industrial equipment and services / 3D printing

Finishing parts

Finishing is the work done on a printed part after it leaves the printer: removing supports and loose powder, washing and curing resin, smoothing, coloring, heat-treating, pressing and machining it until it is fit to use.

7

Milestones achieved, from 1999 to 2018.

3

To watch for: announced, not yet confirmed outside.

2

Open deliverables. Nobody has shipped them.

The road

AchievedWatch forOpen

Achieved

  1. 1999

    Supports that dissolve

    Stratasys introduced its WaterWorks support removal system with the FDM 3000 printer in late 1999, according to the company's annual report for 2002. The printer builds temporary supports from a second material, and the part is then soaked in a water-based solution that dissolves them. Stratasys said this "eliminates most post-processing requirements." The bath is alkaline: by the account of PADT, a Stratasys reseller, its sodium hydroxide and sodium carbonate break the support polymer's ester bonds and turn it into salts that dissolve in water.

    sec.govpadtinc.com

    Credit

    Stratasys

  2. 2002

    Milling inside the printer

    Matsuura Machinery of Fukui Prefecture, Japan, unveiled the M-PHOTON 25Y at the JIMTOF trade show in 2002. It sintered metal powder layer by layer with a laser and finished the surface with high-speed milling in the same machine as the part was built, so a mold could be made in one process. Matsuura calls it the "world's first hybrid metal 3D printer." The work grew from a regional research program begun in Fukui in 2000 that aimed to cut mold-making time to about a third, and the company's LUMEX machines carried the idea on from 2004.

    matsuura.co.jpnippon.com

    Credit

    Matsuura Machinery

  3. 2015

    Dyeing printed nylon

    In September 2015 Hans J. Langer, founder of the printer maker EOS, became an investor in DyeMansion, a Munich start-up that colors laser-sintered nylon parts and then polishes and waterproofs them. By the company's account the process gave colors that resist UV light and solvents and cut the yellowing common in laser-sintered parts. Founders Felix Ewald and Philipp Kramer found the niche in 2013, and TCT Magazine gives 2015 as the founding year. In October 2023 DyeMansion delivered its 1,000th finishing system, a Powerfuse S vapor smoothing unit, to ZEISS Vision Care.

    tctmagazine.comtctmagazine.com

    Credit

    Felix Ewald and Philipp Kramer, DyeMansion

  4. 2016

    Limits of pressing out pores

    Hot isostatic pressing, or HIP (heating a part in high-pressure gas to close internal pores), began at Battelle Memorial Institute in Columbus, Ohio, as a way to bond Zircaloy-clad nuclear fuel elements; ASME dates the first vessels to 1956. In 2016 a team used X-ray computed tomography (CT, 3D X-ray scanning) to follow single pores in titanium alloy (Ti-6Al-4V) parts printed by electron-beam melting. A standard HIP cycle shrank internal pores below the scanner's limit of about 5 µm, except defects connected to the surface. A second paper the same year found that round pores holding argon gas came back and grew during later high-temperature heat treatment.

    LessonHIP cannot close pores that open to the surface, and pores holding argon can grow back in a later heat treatment.

    asme.orgeprints.whiterose.ac.ukeprints.whiterose.ac.uk

    Credit

    Battelle Memorial Institute (origin); S. Tammas-Williams, P.J. Withers, I. Todd and P.B. Prangnell (2016 findings)

  5. 2017

    Wash and cure machines

    On 8 May 2017 Formlabs of Somerville, Massachusetts, announced Form Wash and Form Cure for parts from its resin printers. Form Wash stirs parts in isopropyl alcohol with an impeller and lifts them out when the cycle ends. Form Cure post-cures them (finishes hardening the resin) with 405 nm light and heat, which Formlabs says its biocompatible resins require. The two machines cost $499 and $699 and began shipping in September 2017, as 3D Printing Industry reported.

    formlabs.com3dprintingindustry.com

    Credit

    Formlabs

  6. 2018

    Vapor smoothing for nylon

    Stratasys had sold a Smoothing Station for ABS plastic parts since December 2008. By September 2018 Additive Manufacturing Technologies (AMT) of Sheffield, England, was offering PostPro3D, priced at about €75,000, to smooth nylon and elastomer parts. Parts hang in a chamber and are exposed to a strong solvent that removes layer lines so they look injection-molded, and AMT says dimensions change by no more than about 0.4%. The method came out of five years of research at the University of Sheffield. By November 2025 AMT counted more than 250 installations of its PostPro SFX machine (the company's count).

    digitalengineering247.com3dprint.com3dprintingindustry.com3dprintingindustry.com

    Credit

    AMT (Joseph Crabtree) and the University of Sheffield

  7. 2018

    Depowdering planned from CAD

    Loose metal powder must be shaken out of printed parts, including their internal cooling channels. In October 2018 Solukon of Augsburg and Siemens announced the SFM-AT800-S, which turns a part endlessly on two motorized axes, and Siemens was building software that reads the CAD file to work out the motion that drains each channel. The pair won the TCT Post Processing Award in 2019, and Solukon launched the software as SPR-Pathfinder in October 2022, pairing the rotation with adjustable vibration. Nikon installed a Solukon machine running SPR-Pathfinder in November 2025.

    Lessonsome channels cannot be emptied once printed, so Solukon's newest software is meant to check whether powder can get out while the part is still being designed.

    tctmagazine.comtctmagazine.com3dprintingindustry.com

    Credit

    Solukon (Andreas Hartmann) and Siemens (Christoph Kiener)

Watch for

  1. Ultrasound shakes off supports

    Fraunhofer IAPT says it can remove supports from metal powder-bed parts automatically by sending high-frequency vibration into the part. Shaking tuned to each part, plus supports redesigned for it, concentrates stress where the supports attach. The institute says supports come off "within a few minutes" with no residue and no manual work. The method comes from the Sonodent project, funded in May 2026, was developed with dental parts in mind, and is on show at Formnext, 17 to 20 November 2026. A patent application has been filed, and beyond "a few minutes" the institute has published no times, costs or quality figures.

    Achieved whena dental lab or manufacturer outside Fraunhofer, or an independent test, publishes removal times and residue checks for a production batch.

    iapt.fraunhofer.de

    Claimed by

    Fraunhofer IAPT, September 2026

  2. Unpacking joined to smoothing

    AMT says its PostPro UP digs printed plastic parts out of the unfused powder cake with vibration, compressed air and a rotating drum, so no one has to scrape them out by hand. It connects to AMT's Digital Manufacturing System, which the company describes as a "single automated line" from unpacking through depowdering, vapor smoothing, coloring and inspection. PostPro UP fits HP Multi Jet Fusion, EOS P3 and Stratasys SAF printers, starts at €80,000, and was due to ship in the first quarter of 2026.

    Achieved whena customer outside AMT reports running builds from unpacking to smoothed part with no manual handling, and publishes throughput or labor figures.

    3dprintingindustry.com3dprint.com

    Claimed by

    AMT, November 2025

  3. Depowdering predicted before printing

    Solukon's SPR-Pathfinder PRO simulates up to one million powder particles (up from 50,000) to find places where powder will get trapped, and predicts how long depowdering will take. Solukon calls the time predictions accurate but has published no error margins and no comparison of predicted against actual times.

    Achieved whena user outside Solukon publishes predicted versus measured depowdering times, with CT scans or weighing that show the channels came out clean.

    3dprintingindustry.com

    Claimed by

    Solukon, July 2026

Open

  1. 01

    Robot clips desktop supports

    A low-cost robot arm with a wrist camera that removes the supports from plastic parts made on a desktop filament (FDM) printer, using a flush cutter or scraper, and leaves the part undamaged.

    The brief
    Credit · unclaimed
  2. 02

    How much powder stays inside

    A public table of how much powder is still inside internal channels after normal cleaning, measured on nylon test parts with channels of several diameters and bends, ordered from several Multi Jet Fusion or laser-sintering service bureaus. Each part is weighed as received, dried and cleaned until its weight stops falling, and weighed again; a subset is CT-scanned at a bureau or lab that offers it. Nylon parts ordered already printed keep metal powder out of the reader's hands.

    The brief
    Credit · unclaimed

Open 01 · the brief

Robot clips desktop supports

Credit · unclaimed

The first to publish is credited on this line, and the deliverable moves from Open to Achieved.

What to build

A low-cost robot arm with a wrist camera that removes the supports from plastic parts made on a desktop filament (FDM) printer, using a flush cutter or scraper, and leaves the part undamaged.

Why it is still open

Post-processing makes up nearly 27% of the cost of printed parts, by Wohlers Associates' research for Wohlers Report 2021, which drew on 124 service providers in 27 countries. Searches of papers, GitHub, Hackaday and company products in November 2026 found two kinds of automation, neither of them this. For plastic parts, PostProcess Technologies removes the supports of filament and PolyJet parts with detergent sprays and soaking, which works only where the supports are made to dissolve or wash away. For metal parts, robots have been paired with cutting and depowdering: the SALSA project of Renishaw and Additive Automations (2020, early research), Rivelin Robotics with Solukon's depowdering machine (2023), and Fraunhofer IAPT's ultrasonic method (2026). None has been shown cutting supports off desktop plastic prints with an arm and camera, and none publishes a tally of successes and failures. The assembly guide for the SO-101, an open robot arm that is itself 3D-printed, tells builders to remove all support material by hand with a small screwdriver.

laserfocusworld.compostprocess.com3dprintingindustry.comtctmagazine.comhuggingface.co

Built with what exists

An SO-101 arm run with LeRobot, open robot-learning software (see the Note "No download"); a policy trained from a handful of teleoperated demonstrations, for example with NVIDIA GR00T 2 (see the Note "Five demonstrations per task") or Runway Praxis-1 (see the Note "Open robot model weights"); a USB camera; flush cutters; any desktop filament printer and PLA.

  1. First step

    Print 25 copies of one test part with the same supports, and record 50 teleoperated removals with the SO-101 leader arm as training data.

  2. Done looks like

    Twenty filmed attempts on twenty different printed parts, with a published tally of parts fully cleaned, parts with supports left on, and parts damaged, plus the time per part against a person doing the same job.

Open 02 · the brief

How much powder stays inside

Credit · unclaimed

The first to publish is credited on this line, and the deliverable moves from Open to Achieved.

What to build

A public table of how much powder is still inside internal channels after normal cleaning, measured on nylon test parts with channels of several diameters and bends, ordered from several Multi Jet Fusion or laser-sintering service bureaus. Each part is weighed as received, dried and cleaned until its weight stops falling, and weighed again; a subset is CT-scanned at a bureau or lab that offers it. Nylon parts ordered already printed keep metal powder out of the reader's hands.

Why it is still open

The one measured study found is for metal, from one lab: Hunter and colleagues at the University of Birmingham (International Journal of Advanced Manufacturing Technology, 2020) used X-ray CT and weighing to assess how well powder was removed from channels in laser and electron-beam printed metal parts. For nylon parts as service bureaus actually clean and ship them, searches turned up simulation and sensors but no published check of what is left behind. EOS's July 2025 article on automated depowdering names trapped powder in fluid channels and heat exchangers as the main risk, but describes only Solukon's flow simulation and process logging, not CT or weighing. Solukon's July 2026 release for SPR-Pathfinder PRO publishes no comparison of prediction against result. In 2023 Rivelin Robotics and Solukon listed "robotic sensing to inspect airflow in cleared channels" as a need, not a finished product.

research.birmingham.ac.ukeos.info3dprintingindustry.comtctmagazine.com

Built with what exists

Free CAD software to design a test coupon; online ordering from Multi Jet Fusion service bureaus; a laboratory balance reading to 1 mg; a drying oven; an ultrasonic bath; CT scanning bought as a service.

  1. First step

    Design one coupon with straight, single-bend and double-bend channels at 2, 4 and 6 mm, and request quotes from three bureaus this month.

  2. Done looks like

    A published dataset of at least three bureaus, five coupons each, giving retained powder in milligrams for each channel diameter and bend, with CT images for at least five coupons that confirm the weighing.