BRENNEN

Industries / Energy, water and waste / Environmental services / Stormwater management

Drains and pipes

Building the gutters, inlets, pipes and culverts that collect rain from streets and roofs and carry it away, and deciding how big a storm they must carry.

6

Milestones achieved, from c. 600 BCE to 2021.

2

To watch for: announced, not yet confirmed outside.

2

Open deliverables. Nobody has shipped them.

The road

AchievedWatch forOpen

Achieved

  1. c. 600 BCE

    Rome drains the Forum

    Rome's early kings built the Cloaca Maxima to channel the stream of the Velabrum valley, which the Tiber often flooded, and so dried out the marshy ground where the Forum grew. Rome's heritage office says Livy places the start of the work in the 6th century BCE under Tarquinius Priscus, with Tarquinius Superbus carrying it through to the Tiber; the first conduit was two parallel channels roofed with a double row of flat stone blocks. It has been rebuilt so often that "probably nothing remains of the original drain", in the words of Platner and Ashby's topographical dictionary, but it is still the largest Roman sewer in working order.

    LessonA drain built to carry floodwater out of a valley became the trunk line of a city, and it lasted because each age rebuilt it.

    sovraintendenzaroma.itpenelope.uchicago.edu

    Credit

    Etruscan and Roman builders under the Tarquin kings, as Livy tells it

  2. 1889

    Sizing drains from rain

    Most small drains are still sized with the rational method: peak flow equals a runoff coefficient (the share of rain that runs off) times rain intensity times drainage area, often written Q = CiA. It assumes the peak comes when the whole area is draining at once, after the "time of concentration", the time water takes to arrive from the farthest point. Thomas Mulvany tied a flood's peak to that time in Ireland in 1851; Emil Kuichling's 1889 paper on rainfall and sewer discharge, in the Transactions of the American Society of Civil Engineers, was "perhaps the first to define explicitly a time of concentration" for city drains, according to the hydrologist Keith Beven (2020); David Lloyd-Davies did the same for British sewers in 1906. The US Federal Highway Administration's urban drainage manual (2009 edition) still gives the formula and limits it to areas under 80 hectares (200 acres).

    LessonA one-line formula with plain assumptions, such as rain falling evenly over the whole area, sizes most street drains, and the manuals cap the area because those assumptions fail on large catchments.

    hess.copernicus.orgapi.crossref.orgfhwa.dot.gov

    Credit

    Thomas Mulvany; Emil Kuichling; David Lloyd-Davies

  3. 1961

    One rain atlas nationwide

    The US Weather Bureau's Technical Paper 40 (TP-40), prepared by David Hershfield, mapped how much rain falls in 30 minutes to 24 hours in storms expected once in 1 to 100 years, across the United States. It drew on 200 long-record Weather Bureau stations, more than 1,600 other long records for the rare storms and about 5,000 stations for the regional pattern. Engineers read their design storm, such as "the 10-year storm", from its maps. Its records end in 1958. NOAA Atlas 14 began replacing it in 2004; a 2020 review for the Chesapeake Bay Program found little change for frequent storms but "substantial increases" for rare ones, and a 2019 note by the Texas engineering firm Quiddity said Dallas's drainage manual still used TP-40 for storms longer than 60 minutes.

    LessonA design rule can outlive its data by decades, so drains keep being sized for the rain of the 1950s.

    weather.govchesapeakebay.netquiddity.com

    Credit

    David M. Hershfield, US Weather Bureau, for the Soil Conservation Service

  4. 1977

    Grates safe for bicycles

    A grate inlet is the barred opening in a gutter that lets street water into a drain. Grates with long parallel bars could trap a bicycle wheel, so from 1977 to 1980 the US Bureau of Reclamation tested grates for the Federal Highway Administration, rating them for bicycle safety and measuring how much water each caught; the federal urban drainage manual still builds its inlet-spacing charts on these tests. The tests also showed that clogging by leaves could not be reproduced well in a laboratory, except to show that grates with wider bar spacing pass debris better.

    LessonAn inlet has to pass water and debris while stopping wheels, and how fast it clogs still depends on the street it sits in.

    fhwa.dot.gov

    Credit

    P. H. Burgi, D. E. Gober and C. A. Pugh, US Bureau of Reclamation, for the Federal Highway Administration

  5. 2012

    Streets carry the cloudburst

    On 2 July 2011 close to 100 mm of rain fell on Copenhagen in one hour, and the city put the damage at DKK 5 to 6 billion. Its 2011 adaptation plan had been to store extreme rain in parks and sports grounds until the pipes recovered; the Cloudburst Management Plan of 2012 found that storage could cover only "a minor part" of the need and chose to lead water to the sea along roads, canals and tunnels. This is the "major system" that US federal guidance also describes: the pipes (the "minor system") carry an ordinary design storm, about the 10-year storm, and planned overland routes take what the pipes cannot. Copenhagen's goal is no more than 10 cm of water on streets in a 100-year storm, at a cost of DKK 3.8 billion by 2033.

    LessonPipes cannot be made big enough for the rarest storms, so the streets themselves have to be designed as drains for them.

    climate-adapt.eea.europa.eustateofgreen.comfhwa.dot.gov

    Credit

    City of Copenhagen; Københavns Energi, the city's utility (now HOFOR)

  6. 2021

    Design rain raised for warming

    Japan's land and transport ministry (MLIT) now has cities size their sewer flood defenses for rain made heavier by climate change. A ministry study group's recommendation of June 2020, revised in April 2021, multiplies today's design rainfall by a regional factor, 1.1 in most regions and 1.15 in Hokkaido, the increase expected if warming stays below 2 °C; a draft planning guideline followed in November 2021. The ministry's research institute, NILIM, reported in 2023 that most local governments built their rainfall formulas from the national design guideline, while a few used recent records that may already include climate change.

    LessonA design storm can be set from projected rain rather than only from past records.

    nilim.go.jpnilim.go.jp

    Credit

    MLIT; National Institute for Land and Infrastructure Management (NILIM)

Watch for

  1. A rain atlas with trends

    NOAA says Atlas 15 will replace Atlas 14 as the US standard for design rainfall. Volume 1 will account for changes already seen in the records, and Volume 2 will give factors for rain through 2100 from climate models, which NOAA says is a first. A pilot for Montana came out on 26 September 2024; NOAA now gives "no earlier than September 2026" for preliminary estimates for the lower 48 states and no earlier than September 2027 for final ones. ENR reported that work on the second phase was paused in summer 2025 and then resumed.

    Achieved whenVolume 1 is published after its 60-day public review, and state transportation departments or city drainage manuals adopt it for design.

    water.noaa.govenr.com

    Claimed by

    NOAA, on its Atlas 15 page as read in November 2026

  2. A tunnel under Main Street

    Howard County, Maryland, is boring an 18-foot (5.5 m) tunnel through granite to carry up to 26,000 US gallons (about 98 m³) of runoff a second from Ellicott City's West End to the Patapsco River, so that flash floods stop running down Main Street; three of five planned upstream holding ponds are built. The county's program has grown from a projected $140 million to about $386 million, and the tunnel is due in late 2027.

    Achieved whenthe tunnel is in service and a storm on the scale of the 2016 or 2018 floods passes without flooding Main Street, as recorded by stream gauges or the National Weather Service.

    marylandmatters.org

    Claimed by

    Howard County, as reported by Maryland Matters and WTOP, July 2026

Open

  1. 01

    A pipe check for towns

    A free tool that screens every storm pipe in a town for whether it can carry today's design storm. It reads the town's public map of storm pipes (diameter, slope, material), draws the area draining to each pipe from lidar elevation data, takes rainfall from NOAA Atlas 14, and applies the rational method and Manning's formula for pipe flow to flag pipes that would run over full.

    The brief
    Credit · unclaimed
  2. 02

    Which rain towns design for

    A public table of the design storm each town's drainage rules require, for example pipes for the 10-year storm and streets for the 100-year storm, the rainfall data the rules name (TP-40 from 1961, Atlas 14 or a local study) and the year of the rule, with a link and a quoted line for every row.

    The brief
    Credit · unclaimed

Open 01 · the brief

A pipe check for towns

Credit · unclaimed

The first to publish is credited on this line, and the deliverable moves from Open to Achieved.

What to build

A free tool that screens every storm pipe in a town for whether it can carry today's design storm. It reads the town's public map of storm pipes (diameter, slope, material), draws the area draining to each pipe from lidar elevation data, takes rainfall from NOAA Atlas 14, and applies the rational method and Manning's formula for pipe flow to flag pipes that would run over full.

Why it is still open

Large cities answer this question with full computer models built by consultants: Seattle Public Utilities' 2020 capacity evaluation modeled 432 miles (695 km) of drainage pipe, 92% of its network, in EPA's Storm Water Management Model (SWMM) for 5- to 50-year storms. Small towns rarely have such models. Open code exists for the single calculations, such as the MIT-licensed hydro-tools library (rational method, Manning capacity). For road culverts, CivicMapper's Culvert Analysis Toolkit, GIS tools for ArcGIS Pro built on a peak-flow model from Cornell University's Soil and Water Lab, already estimates capacity from map and elevation data, and Imperial College London's SWMManywhere builds a made-up network where no pipe map exists (see Flood models and warnings). Searches found no free tool that screens a town's real street pipes from public data, and no test of how well a quick screen agrees with a full model.

seattle.govgithub.comcivicmapper.github.io

Built with what exists

QGIS; WhiteboxTools to draw drainage areas; USGS 3DEP lidar; NOAA Atlas 14 rainfall; Python with hydro-tools; EPA SWMM to check a sample; an AI coding agent to write the glue code.

  1. First step

    Ask Seattle Public Utilities for the pipe-by-pipe results behind its 2020 evaluation, and download one small town's public storm-pipe map.

  2. Done looks like

    For a city that has a full model, the share of the model's under-capacity pipes that the screen also flags and the share of flagged pipes the model calls adequate, published with the code; then screens for three towns that have no model.

Open 02 · the brief

Which rain towns design for

Credit · unclaimed

The first to publish is credited on this line, and the deliverable moves from Open to Achieved.

What to build

A public table of the design storm each town's drainage rules require, for example pipes for the 10-year storm and streets for the 100-year storm, the rainfall data the rules name (TP-40 from 1961, Atlas 14 or a local study) and the year of the rule, with a link and a quoted line for every row.

Why it is still open

Reviews exist at state level; a 2020 review of the Chesapeake Bay states' manuals found that their rainfall sources "vary significantly by age of record". But towns and counties write their own rules, and cases such as Dallas's use of TP-40 for longer storms turn up only one at a time in engineers' notes. Searches found no national town-by-town count.

chesapeakebay.netquiddity.com

Built with what exists

Online code libraries such as eCode360 and Municode, and city drainage manuals; a browser agent such as Browser Use to find and read them (see the Note "Deleting 80% to start over"); an AI model to pull out the fields; people to check a sample.

  1. First step

    Take the 50 largest towns in one state, find their drainage rules by hand and settle the table's columns.

  2. Done looks like

    500 US towns and cities, each row with a source link and quote; a person checks 50 rows chosen at random and the error rate is published; a count of how many still name TP-40.