Industries / Consumer goods / Sporting goods
Footwear
Footwear work designs and makes shoes for running, court and field sports: the upper that holds the foot, the midsole foam that cushions it, and the outsole that grips the ground.
7
Milestones achieved, from 1924 to 2020.
2
To watch for: announced, not yet confirmed outside.
2
Open deliverables. Nobody has shipped them.
The road
AchievedWatch forOpen
Achieved
1924
Brothers register a shoe factory
Adi Dassler and his brother Rudolf registered the Gebrüder Dassler Schuhfabrik in Herzogenaurach, Bavaria, after starting out in their mother's laundry room, to make shoes for athletes. By adidas's account, athletes won gold medals in its shoes at the 1928, 1932 and 1936 Olympics. On 18 August 1949 Adi registered his own company, adidas, with 47 employees in the same town.
Credit
Adolf (Adi) and Rudolf Dassler
1972
A studded one-piece outsole
Bill Bowerman filed a US patent in August 1972 for an athletic shoe whose rubber outsole is a field of small, square studs molded in one piece with the sole, so the studs alone touch the ground. Beneath it sits a middle sole softer than the outsole, and the upper is layered nylon fabric and foam. The patent was granted in February 1974 to BRS, Inc., the Oregon company that merged into Nike in 1982.
Credit
William J. Bowerman, BRS, Inc. (later Nike)
1978
Gas sealed in the sole
Marion Frank Rudy patented an insole of welded polyurethane layers that holds a gas, such as sulfur hexafluoride, that leaks out so slowly the cushion stays inflated for years; he first proposed it to Nike in 1977. Nike put it in the Tailwind, which by Nike's account was its first shoe with an Air-sole unit. It went on sale at six Honolulu shops for the Honolulu Marathon in late 1978 and more widely in 1979.
Credit
Marion Frank Rudy; Nike
2005
Factory list made public
After years of criticism over its labor practices, Nike published the names and locations of more than 700 contract factories making its shoes, clothing and equipment, with its corporate responsibility report in April 2005. The same report said Nike audited 569 factories in 2003 and 2004 and found "abusive treatment" in more than a quarter of its South Asian factories. Reebok had already listed all its footwear factories, the Associated Press reported.
LessonPublishing where products are made lets outsiders check conditions, which a company's own audits cannot do alone.
Credit
Nike
2013
Boost foam from BASF
adidas launched the Energy Boost running shoe with a new midsole cushioning material made with BASF, the German chemical company. adidas describes it as soft and responsive at once, which runners had thought were opposites. Foam made by a chemical supplier, not the shoe brand, then became a main way running shoes compete.
Credit
adidas and BASF
2019
Robot factories closed
adidas built two highly automated "Speedfactories" with Oechsler, a German plastics company, in Ansbach, Germany, and Atlanta, USA, to make shoes near their buyers instead of in Asia. In November 2019 it said production at both would end by April 2020 at the latest and that the methods would move to two suppliers in Asia. adidas kept working with Oechsler on 3D-printed "4D" soles, a printing method adidas first used in 2017 with the company Carbon.
LessonAutomating a few steps did not make Western production pay; adidas said the change would make better use of its suppliers' existing capacity.
Credit
adidas; Oechsler
2020
Limits on super shoes
"Super shoes" pair a thick, springy foam with a stiff plate. In a Nike-funded study, Nike's prototype cut the energy cost of running by about 4% against two established marathon shoes in all 18 runners tested (Hoogkamer and colleagues, 2018). A study funded by Grand Valley State University found the Vaporfly 4.2% more economical than an adidas marathon shoe (Barnes and Kilding, 2019). On 31 January 2020 World Athletics, the sport's governing body, limited road-shoe soles to 40 mm thick, allowed one rigid plate, and from 30 April 2020 required any shoe raced in to have been on open sale for four months.
LessonWhen a shoe changes results, the sport may cap the design instead of banning it.
Credit
Nike (Vaporfly); World Athletics
Watch for
Powered shoes for joggers
Nike says Project Amplify, built with the robotics company Dephy, is "the world's first powered footwear system for running and walking": a small motor, drive belt and battery cuff fitted to a carbon-plated running shoe. It is aimed at people running a mile in 10 to 12 minutes. Nike says more than 400 athletes have covered over 2.4 million steps in its tests, and that the product is "still early in testing", with a broad launch "in the coming years".
Achieved whena lab outside Nike and Dephy publishes how much effort or energy it saves, or the system goes on sale.
Claimed by
Nike, October 2025
Robot-sprayed uppers at volume
On, the Swiss running brand, makes the upper of some shoes in one piece by having a robot arm spray 1.5 km of thermoplastic filament around a shoe-shaped form, in place of a process On says can take about 200 steps. It opened a site near Busan, South Korea, in April 2026 that it says can make 1,500 pairs a day, against 150 at its first site in Zurich. On has not disclosed the cost per pair, and the rest of the shoe is still made in a separate process.
Achieved whenan outside party, such as an auditor or a visiting reporter given output figures, confirms the Busan site's actual output, not just its capacity.
Claimed by
On, July 2026 (reported by Glossy)
Open
01
Bite lines found by scanner
A public set of 3D scans of athletic shoe uppers pulled onto their lasts, the foot-shaped forms shoes are built on, each with the "bite line" a skilled worker traced: the line where the sole will meet the upper, which tells workers where to roughen and glue. Add software that predicts the line from a scan, and have a small robot arm draw it with a washable pen.
The briefCredit · unclaimed02
Midsoles measured as they wear
A public, growing table of how running-shoe midsoles lose cushioning and spring as they wear. Each model is measured new and again every 100 km up to 800 km, on the same drop-impact rig, using pairs that volunteer runners log on a GPS watch.
The briefCredit · unclaimed
Open 01 · the brief
Bite lines found by scanner
The first to publish is credited on this line, and the deliverable moves from Open to Achieved.
What to build
A public set of 3D scans of athletic shoe uppers pulled onto their lasts, the foot-shaped forms shoes are built on, each with the "bite line" a skilled worker traced: the line where the sole will meet the upper, which tells workers where to roughen and glue. Add software that predicts the line from a scan, and have a small robot arm draw it with a washable pen.
Why it is still open
A patent filed by Nike, now also assigned to Pou Chen, one of the largest athletic shoe makers, says the bite line has traditionally been traced by hand and that the older method takes three or more manual steps (granted November 2022). Nike has patented ways to build 3D models of shoe parts from a laser line and a camera, so that steps such as gluing can be automated, since a filing of November 2011. Robot gluing of soles from 3D scans has been studied since at least 2009 and again in 2025, and On's robot-made uppers still join the rest of the shoe in a separate process. Searches of GitHub, Hugging Face and Zenodo in November 2026 found no public set of upper scans with marked bite lines.
Built with what exists
a structured-light 3D scanner or a phone with a depth sensor; Open3D to clean and align the scans; a point-cloud segmentation model trained in PyTorch; a low-cost arm such as the SO-101 used with Hugging Face's LeRobot software, taught to trace from a few human demonstrations with a robot model such as NVIDIA's GR00T 2 (see the Note "Five demonstrations per task").
First step
Ask a footwear design school or a shoe sample room to let you scan ten lasted uppers before and after a worker marks them.
Done looks like
At least 200 scanned uppers across 10 or more styles and sizes, each with its traced line, released under an open license; and a published result on 40 held-out uppers giving the median gap between the predicted and traced line in millimeters and the share of the line within 2 mm.
Open 02 · the brief
Midsoles measured as they wear
The first to publish is credited on this line, and the deliverable moves from Open to Achieved.
What to build
A public, growing table of how running-shoe midsoles lose cushioning and spring as they wear. Each model is measured new and again every 100 km up to 800 km, on the same drop-impact rig, using pairs that volunteer runners log on a GPS watch.
Why it is still open
The study most often cited on worn super shoes tested one pair of prototypes, PEBA and EVA foam, new and after 450 km, with 22 runners. It found that the PEBA shoe's running-economy advantage over EVA had gone after 450 km (Rodrigo-Carranza and colleagues, 2023). A 2026 preprint from Stanford by Jeremy McCulloch and Ellen Kuhl found the opposite for the foam itself: in one elite racing shoe worn for 300 miles, the midsole foam kept its stiffness and energy return. Each study tested a single model. Testers such as RTINGS, which says it has bought and tested 314 running shoes, publish measurements of shoes they buy, and ASTM's impact test for athletic shoe cushioning, F1976, was withdrawn in 2022. No shared data following many commercial models through their wear was found.
Built with what exists
a drop rig with a fixed weight and a high-g accelerometer read by an Arduino or Raspberry Pi; a Shore durometer for foam hardness; runners' GPS watch logs for distance; Python for analysis.
First step
Build the drop rig and test five pairs of retired running shoes against new pairs of the same models from a local running club.
Done looks like
Ten shoe models, three pairs each, measured at 0, 100, 200 and so on up to 800 km, with the rig drawings and raw data public; for each model, the percent change in peak impact and in energy returned at 400 and 800 km, and a repeat-test spread on the same shoe below 3%.