BRENNEN

Industries / Media, arts and recreation / Media and entertainment / Radio broadcasting

Transmitters

Transmitter work is getting the signal out: the transmitters, antennas and towers for AM, FM, long wave and shortwave, and the choice of power and frequency.

4

Milestones achieved, from 1934 to 2026.

1

To watch for: announced, not yet confirmed outside.

2

Open deliverables. Nobody has shipped them.

The road

AchievedWatch forOpen

Achieved

  1. 1934

    Half a million watts

    WLW in Cincinnati, owned by Powel Crosley Jr.'s Crosley Radio Corporation, began broadcasting at 500 kW, ten times the 50 kW it had used before, with an amplifier of 12 water-cooled vacuum tubes rated at 100 kW each. Its chief engineer, Joseph Chambers, reported in an October 1934 paper that the higher power was the "most effective static eliminator yet devised," but WLW also interfered with CFRB in Toronto, 10 kHz away. After FCC hearings on superpower broadcasting that began in November 1936, the FCC limited US stations to 50 kW and WLW had to cut back, by the IEEE Cincinnati Section's account.

    LessonOne very strong station reached distant rural listeners but spilled into its neighbors' channels, and the regulator chose many smaller stations over a few giants.

    ieeecincinnati.org

    Credit

    Crosley Radio Corporation (Powel Crosley Jr., Joseph A. Chambers)

  2. 1945

    FM moves up the dial

    FM (frequency modulation) carries sound by varying the frequency of the radio wave rather than its strength. Edwin Armstrong turned on the carrier of his FM station W2XMN at Alpine, New Jersey, on 10 April 1938, and commercial FM began on 42–50 MHz on 1 January 1941. On 27 June 1945 the FCC moved FM to 88–108 MHz, keeping 88–92 MHz for noncommercial stations, and a July 1946 order eliminated the lower band. NAB Reports in 1945 described the "old FM band between 42-50 megacycles" and the "new FM band between 88-108 megacycles," and Armstrong was still in court in January 1949 to stay on 44.1 MHz.

    LessonThe band was moved after stations had launched, and they had to rebuild on new frequencies.

    losthistory.networldradiohistory.com

    Credit

    Edwin H. Armstrong; the FCC

  3. 1961

    FM goes stereo

    In the late 1950s the FCC considered 14 proposed systems for stereo FM, and in April 1961 it approved a joint General Electric–Zenith system. It keeps left plus right as the main channel and adds the difference on a 38 kHz subcarrier, with a 19 kHz pilot tone that receivers use to recover it. Regular stereo FM began on 1 June 1961: GE's WGFM in Schenectady, New York, went first at midnight Eastern time, and WEFM in Chicago followed an hour later at local midnight.

    radioworld.com

    Credit

    General Electric; Zenith; the FCC

  4. 2026

    Long wave goes dark

    The BBC's long-wave service on 198 kHz, carrying BBC Radio 4, closed at 1 am BST on 27 June 2026, shutting the transmitters at Droitwich (Wychbold), Westerglen and Burghead. The Wychbold masts had broadcast since 1934, letting one site cover the whole UK, and carried Neville Chamberlain's declaration of war in 1939 and, later, the Shipping Forecast and ball-by-ball cricket on Test Match Special.

    rsgb.orgt3.com

    Credit

    the BBC

Watch for

  1. Japan leaves AM

    44 of Japan's 47 commercial AM stations have announced plans to stop AM broadcasting by autumn 2028 and move to FM. In an April 2026 article for mediumwave.info, Shinobu Unakami gives two causes: the spread of Wide FM, which puts AM stations' programs on FM, and ageing equipment. Japan's Ministry of Internal Affairs and Communications (MIC) issued a policy in March 2023, amended in December 2024, that lets stations suspend AM for a period before closing it, and on 30 March 2026 the public broadcaster NHK cut its three radio services to two, taking Radio 2 off the air.

    Achieved whenthe stations' AM transmitters are off the air after autumn 2028, as MIC licence records show, and listening figures from before and after are published.

    soumu.go.jpmediumwave.info

    Claimed by

    Japan's commercial AM broadcasters and the MIC; latest report April 2026

Open

  1. 01

    Map the AM noise floor

    Fixed receivers in several cities that log the noise level on empty AM channels around the clock for a year, with a public map and dataset, so that engineers and regulators can see whether electrical noise from lights, chargers and power supplies is rising, and where.

    The brief
    Credit · unclaimed
  2. 02

    Redraw AM coverage for cities

    Measured coverage maps for AM stations in dense cities, made from drive tests with a calibrated receiver, set beside the coverage that the FCC's prediction methods give.

    The brief
    Credit · unclaimed

Open 01 · the brief

Map the AM noise floor

Credit · unclaimed

The first to publish is credited on this line, and the deliverable moves from Open to Achieved.

What to build

Fixed receivers in several cities that log the noise level on empty AM channels around the clock for a year, with a public map and dataset, so that engineers and regulators can see whether electrical noise from lights, chargers and power supplies is rising, and where.

Why it is still open

In 2016 the FCC's Technological Advisory Council opened an inquiry (ET Docket 16-191) asking whether radio noise was increasing and for quantitative evidence. Radio World reported in 2017 that respondents were "virtually unanimous in calling for an official noise study." The most recent study found, NRSC-R102 (January 2025), measured noise on three empty AM channels along one 50-mile drive from Germantown to Baltimore, Maryland. That is a snapshot of one area, not a trend over time.

radioworld.comnrscstandards.org

Built with what exists

Software-defined radios with HF coverage, such as KiwiSDR or Airspy HF+ receivers, with active loop antennas; a Raspberry Pi at each site; Python for logging; NRSC-R102's method and levels as the calibration reference.

  1. First step

    Set up one receiver and loop antenna at an urban site, log three empty channels for a month, and compare the readings with NRSC-R102's urban figures.

  2. Done looks like

    10 sites in at least three cities logged for 12 months; hourly noise levels on at least three clear AM channels per site, calibrated against a field-strength meter, published as open data with the month-to-month change and its uncertainty.

Open 02 · the brief

Redraw AM coverage for cities

Credit · unclaimed

The first to publish is credited on this line, and the deliverable moves from Open to Achieved.

What to build

Measured coverage maps for AM stations in dense cities, made from drive tests with a calibrated receiver, set beside the coverage that the FCC's prediction methods give.

Why it is still open

NRSC-R102 found that building clutter can cut AM field strength by a factor of up to 100 (40 dB), "which are not accounted for in signal coverage maps," and that measured fields can be well below what the usual ground-wave models predict. Its measurements cover three 50 kW stations on one route in the Baltimore and Washington area.

nrscstandards.org

Built with what exists

A software-defined radio and calibrated active antenna, checked against a field-strength meter such as the Potomac Instruments FIM-41 used in the NRSC study; a GPS logger; the FCC's published AM station data for the predictions; QGIS for the maps.

  1. First step

    Drive one station's predicted strong-signal area through one dense downtown and one suburb with an SDR and GPS logger, and plot measured against predicted.

  2. Done looks like

    20 stations in three cities driven on a street grid; for each station, the area where the measured signal is above a stated level (NRSC-R102 found 3 to 5 mV/m generally good for mobile listening) compared with the predicted area, published with the raw data.