BRENNEN

Industries / Technology / Lasers and photonics

Laser sources

Laser sources is the work of designing and building the lasers themselves: the gas tubes, crystals, semiconductor chips and glass fibers that turn electricity into a narrow beam of one color, and the companies that make and sell them.

7

Milestones achieved, from 1960 to 2024.

2

To watch for: announced, not yet confirmed outside.

2

Open deliverables. Nobody has shipped them.

The road

AchievedWatch forOpen

Achieved

  1. 1960

    A beam that stays on

    Maiman's ruby laser gave only flashes. On 12 December 1960 at Bell Labs in New Jersey, Ali Javan, William Bennett and Donald Herriott ran a laser in an electric discharge through helium and neon gas; MIT calls it the first gas laser and the first to give a continuous beam. Bell Labs had to license its inventions to other companies, and Spectra-Physics, founded in September 1961, and Perkin-Elmer exhibited helium-neon lasers for about $8,000 in March 1962 and sold their 75th in June 1963, by Jeff Hecht's account.

    news.mit.eduoptica-opn.org

    Credit

    Ali Javan, William Bennett and Donald Herriott, Bell Labs

  2. 1962

    Light from a junction

    A semiconductor laser, or diode laser, makes light where current crosses the junction between two layers of a crystal such as gallium arsenide, with no lamp to pump it. In the autumn of 1962, General Electric's laboratories in Schenectady and Syracuse, IBM's Watson Research Center and MIT Lincoln Laboratory each reported one independently, within about a month of each other, by the account of the IEEE, which dedicated a Milestone plaque to the four groups in February 2024.

    ethw.org

    Credit

    Robert N. Hall's group at GE Schenectady; Nick Holonyak Jr. and S. F. Bevacqua at GE Syracuse; Marshall Nathan's group at IBM; Theodore Quist, Robert Rediker and colleagues at Lincoln Laboratory

  3. 1964

    Carbon dioxide for power

    Kumar Patel at Bell Labs calculated that carbon dioxide gas should lase near 10 µm, and it gave tens of milliwatts on the first try; his paper on continuous laser action in CO2 appeared in Physical Review on 30 November 1964. Adding nitrogen raised the output from 10 mW to 10 W, then the highest continuous power seen from any laser, and he had 200 W by mid-1965. Eugene Watson left Spectra-Physics to found Coherent Radiation Laboratories, now Coherent, to make CO2 lasers, which Hecht writes remain the main industrial laser at long infrared wavelengths.

    optica-opn.orgapi.crossref.org

    Credit

    C. Kumar N. Patel, Bell Labs

  4. 1977

    A patent after 18 years

    Arthur Schawlow and Charles Townes set out the laser in theory in Physical Review in December 1958. Gordon Gould had written his own ideas in a notebook titled "Some rough calculations on the feasibility of a LASER", which the National Inventors Hall of Fame calls the first use of the acronym, but misunderstood an attorney's advice and did not file for a patent until 1959, after others. His application went through five separate interference proceedings, the Patent Office's contests over who invented first, and his first basic laser patent was issued only in 1977; a second basic patent, US 4,704,583, followed on 3 November 1987. The National Inventors Hall of Fame says the lasers his patents cover are used in 80 percent of industrial, commercial and medical laser applications.

    Lessonfiling late, in one application that held many inventions, cost him 18 years of contests.

    invent.orgapi.crossref.org

    Credit

    Gordon Gould

  5. 1985

    Stretch, amplify, compress

    A very short, intense pulse destroys the amplifier it passes through. Donna Strickland and Gérard Mourou stretched the pulse in time to lower its peak power, amplified it, and then compressed it again; their 1985 article was the foundation of Strickland's doctoral thesis at the University of Rochester. The method, chirped pulse amplification (CPA), became the standard for high-intensity lasers, and the Nobel committee, which gave them half of the 2018 physics prize, lists the millions of corrective eye operations done each year among its uses.

    nobelprize.org

    Credit

    Donna Strickland and Gérard Mourou

  6. 1996

    Violet light from a diode

    In January 1996, at the Photonics West conference in San Jose, Shuji Nakamura of Nichia Chemical Industries in Tokushima, Japan, reported a diode laser of indium gallium nitride (InGaN) that emitted at 417 nm at room temperature when driven by pulses of current; earlier lasers of gallium nitride had to be pumped by another laser. Nakamura's own profile says InGaN layers now underlie all violet, blue and green semiconductor lasers.

    laserfocusworld.comssleec.ucsb.edu

    Credit

    Shuji Nakamura, Nichia

  7. 2024

    A fiber laser leader shrinks

    A fiber laser makes its beam inside a glass fiber doped with a rare earth such as ytterbium. IPG Photonics, which began operations in 1990, reported in its annual report to the US Securities and Exchange Commission sales of $857 million for materials processing in 2024, down from $1,153 million in 2023, a fall of about 26%. It names Wuhan Raycus and Maxphotonics of China among its rivals and says many competitors are raising the power of their fiber lasers and cutting prices; China fell from 34% of its sales in 2022 to 25% in 2024. It also had to add capacity elsewhere to replace factories in Russia and Belarus lost to sanctions, and disposed of its Russian subsidiary in 2024. Optech Consulting, a market analyst, counted the whole world market for materials-processing lasers at $5.0 billion in 2024, down 7.5%, and put the larger fall in lasers than in laser machines down to lower prices under "fierce competition by laser manufacturers in China."

    Lessononce a laser type is standard, price and the place of manufacture decide who sells it.

    sec.govoptech-consulting.com

    Credit

    IPG Photonics; Wuhan Raycus; Maxphotonics; Optech Consulting for the market count

Watch for

  1. Six-inch indium phosphide wafers

    The lasers in data center optics are made on wafers of indium phosphide (InP); Coherent's older lines use wafers 3 inches across. Coherent says it now makes three kinds of transceiver parts on 6-inch InP wafers in Sherman, Texas, and Järfälla, Sweden: EMLs (lasers with a built-in light switch), continuous-wave lasers and photodiodes. It says a 6-inch wafer gives more than four times as many chips as a 3-inch one at less than half the cost, and that its 6-inch yields exceed those of its 3-inch lines.

    Achieved whena party outside Coherent, such as a customer or a teardown firm, confirms 6-inch InP lasers in shipping products, or yield figures are published and checked outside the company.

    fool.com

    Claimed by

    James Anderson, Coherent's chief executive, on the earnings call of 4 February 2026

  2. A 2.0 kW diode bar

    A laser diode bar is a row of diode lasers on one chip about 1 cm wide, used to pump other lasers and to process material. Hamamatsu Photonics says it got 2.0 kW of quasi-continuous output (long pulses of more than 100 µs at a high repetition rate) from a 1 cm single-junction bar at room temperature, after new treatment of the chip's end faces, and that this exceeds the 1.9 kW a German research institute reported in 2022. The work was funded by Japan's NEDO and was to be presented at the International Semiconductor Laser Conference in Tampere, Finland, from 14 June 2026.

    Achieved whena laboratory outside Hamamatsu measures 2.0 kW from such a bar under the stated conditions, or bars with that rating go on sale and buyers' tests confirm it.

    photonicsonline.com

    Claimed by

    Hamamatsu Photonics, June 2026

Open

  1. 01

    Public fiber laser price record

    A dated public record of advertised prices for continuous-wave fiber laser sources from 1 kW to 30 kW, taken each month from public price lists, distributor and marketplace listings and published tender awards, with the price per kilowatt computed for each power class and maker. No laser is bought or switched on.

    The brief
    Credit · unclaimed
  2. 02

    Over-limit pointers counted monthly

    A monthly public count of laser pointers on large online marketplaces in the US, the UK and Australia whose own listing text claims more power, or a higher hazard class, than the country's limit for consumer pointers or the marketplace's own rule, with every flagged listing archived. The work reads listings only; no laser is bought or switched on.

    The brief
    Credit · unclaimed

Open 01 · the brief

Public fiber laser price record

Credit · unclaimed

The first to publish is credited on this line, and the deliverable moves from Open to Achieved.

What to build

A dated public record of advertised prices for continuous-wave fiber laser sources from 1 kW to 30 kW, taken each month from public price lists, distributor and marketplace listings and published tender awards, with the price per kilowatt computed for each power class and maker. No laser is bought or switched on.

Why it is still open

Prices reach the public as one-off charts in trade articles. Bo Gu of BOS Photonics charted a "typical price range" for Chinese fiber lasers in Laser Focus World in 2019 and warned that the chart "may have underestimated the price trend"; IPG's 2024 annual report says only that many competitors are cutting prices. A GitHub search for "fiber laser price" on 20 November 2026 found no repository.

laserfocusworld.com

Built with what exists

A browser agent such as Browser Use to collect listings (see the Note "Deleting 80% to start over"); the Internet Archive's Save Page Now to keep a copy of every page used; a Claude-based document reviewer to pull model, power and price from each listing with a citation for a person to check (see the Note "Seven more flagged"); Python with pandas; a CSV on GitHub. AI agents that read web pages and fill tables are what make a monthly record a one-person job.

  1. First step

    Archive this month's public listings for 1.5, 3, 6 and 12 kW sources from Raycus and Maxphotonics and compute the first four medians.

  2. Done looks like

    Twelve monthly snapshots of at least 150 listings each, covering at least 6 makers (Raycus, Maxphotonics and IPG among them) and at least 3 sales channels; every price archived and linked; currency converted at that day's published exchange rate; a second person re-checks a random 10% of rows and finds at least 98% correct; the median price per kilowatt for each class published with the data.

Open 02 · the brief

Over-limit pointers counted monthly

Credit · unclaimed

The first to publish is credited on this line, and the deliverable moves from Open to Achieved.

What to build

A monthly public count of laser pointers on large online marketplaces in the US, the UK and Australia whose own listing text claims more power, or a higher hazard class, than the country's limit for consumer pointers or the marketplace's own rule, with every flagged listing archived. The work reads listings only; no laser is bought or switched on.

Why it is still open

Checks so far are one-off tests of bought devices. In 2013 NIST measured 122 pointers and found nearly 90% of green and 44% of red ones out of compliance with US federal rules. The UK's Office for Product Safety and Standards acts one listing at a time: on 5 October 2023 it reported three pointers sold via Amazon that tested as Class 3 and Class 4 lasers with wrong safety labels, and the marketplace removed the listings. No recurring public count was found; a GitHub search for "laser pointer listings" on 20 November 2026 returned nothing.

gov.ukoptics.org

Built with what exists

A browser agent such as Browser Use (see the Note "Deleting 80% to start over"); Save Page Now; a language model such as Claude to flag claims in listing text ("1000 mW", "burning", "Class 4") for a person to confirm; a spreadsheet of each country's limits with their legal sources.

  1. First step

    Write the search terms and the list of claim phrases, then archive the first 200 results for "laser pointer" on one marketplace in one country and flag them by hand.

  2. Done looks like

    Six monthly counts in 3 countries on at least 3 marketplaces each; every flagged listing archived with its claim quoted; two people independently check a random 200 flags each month and agree on at least 95%; each month's list sent to the marketplaces and the national regulator, with the share still on sale 30 days later published.